喜歡就充值下載吧。。。資源目錄里展示的全都有，，下載后全都有，，圖紙均為高清圖，，CAD圖紙可自行編輯，，有疑問咨詢QQ:1064457796
塑料手柄注塑模設計
摘要：本設計題目為手柄注塑模設計，體現了塑料制品的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者注塑模的基礎知識，為設計更復雜的注塑模具做好了鋪墊幷吸取了更深刻的經驗。
本設計運用塑料成型工藝及模具設計的基礎知識，首先分析了塑件的成分及性能要求，為選取澆口的類型做好了準備；然后估算了塑件的體積，便于選取注塑機及確定型腔數目；最后分析了塑件的特征，確定模具的設計參數，設計要點，及推出裝置的選取。
通過分析塑料手柄的工藝性，可知塑件采用內抽芯機構進行脫模，由圖可知，手柄為兩個局部段，對應在模具上制成兩個內抽的滑塊，這些滑塊始終不脫離型芯座。由于手柄部分要求嚴格，所以采用側澆口澆注系統，脫模后不在修正澆口的痕跡。但采用這種澆口時，常常要在模具上增加一個分型面，以便澆口凝料脫模。
關鍵詞：工藝分析,塑件成型澆,注系統,模具結構
DESIGN OF INJECTION MOULD
FORPLASTIC HANDLE
摘要：本設計題目為手柄注塑模設計，體現了塑料制品的設計要求、內容及方向，有一定的設計意義。通過對該零件模具的設計，進一步加強了設計者注塑模的基礎知識，為設計更復雜的注塑模具做好了鋪墊幷吸取了更深刻的經驗。
ABSTRACT: This design topic is the handle of the injection mold design, the design of plastic products, content and direction of requirements, the design of a certain significance. Through the design of the die parts, further strengthen the basic knowledge of injection mold designers, paving the way and draw a more profound experience for the injection mold design more complex.
本設計運用塑料成型工藝及模具設計的基礎知識，首先分析了塑件的成分及性能要求，為選取澆口的類型做好了準備；然后估算了塑件的體積，便于選取注塑機及確定型腔數目；最后分析了塑件的特征，確定模具的設計參數，設計要點，及推出裝置的選取。
This design using the basic knowledge of plastic molding process and mold design, first analyzes the composition and performance of the plastic parts, ready to select the type of gate; plastic parts and estimated the volume, to select the injection molding machine and determine the number of cavity; finally analyses the characteristics of plastic parts, the design key points to determine the design parameters die, and selection, launch device.
通過分析塑料手柄的工藝性，可知塑件采用內抽芯機構進行脫模，由圖可知，手柄為兩個局部段，對應在模具上制成兩個內抽的滑塊，這些滑塊始終不脫離型芯座。由于手柄部分要求嚴格，所以采用側澆口澆注系統，脫模后不在修正澆口的痕跡。但采用這種澆口時，常常要在模具上增加一個分型面，以便澆口凝料脫模。
Through the technological analysis of the plastic handle, plastic parts with internal core pulling mechanism of release, it can be seen from the figure, the handle is the two partial sections, corresponding to the mould made of block two pumping, the slider is always not from core seat. The handle part is strict, so the side gate, after stripping without correction gate. But the gate, often to add a parting surface in the mould, so that the gate gas ejector.
關鍵詞：工藝分析 塑件成型 澆注系統 模具結構
KEYWORDS: process analysis,plastic molding ,casting system, die structure