液壓挖掘機行走裝置設計,液壓挖掘機行走裝置設計,液壓,挖掘機,行走,裝置,設計 南昌航空大學科技學院學士學位論文 液壓挖掘機行走裝置設計 學生姓名：樂晨輝 班級：0781052 指導教師：邢普 摘要：。在本次設計中，由于輪式行走機構結構緊湊且工作效率高，通過比較采用了輪胎式行走裝置來滿足設計要求。 根據設計要求，機重為11噸；輪胎規格為9.00-20；輪胎動力半徑r=0.491米。挖掘機最大牽引力P=0.6機重；發動機功率N=58.8KW，轉速2000r/min；油泵最大流量2×100l/min；最大工作壓力21MPa。最高行駛速度31Km/h，設計取全橋驅動。上部轉臺是全回轉式，因此它可在一個更大的范圍內工作。又因采用液壓機械傳動控制而使整機性能得以改善。與傳統機械式挖掘機相比，其行走能力提高到了很多。本次設計的主要內容為：液壓挖掘機行走裝置方案設計；繪制裝配草圖和總裝配圖；動力源選擇及有關參數的確定；行走裝置牽引力的計算；傳動方式比較與選擇、傳動方案的確定及傳動系統的技術設計；行星減速器及零、部件的設計計算，主要零件強度校核；繪制零、部件圖和總裝配圖，進行仿真設計，編寫設計計算說明書。 本設計的主要特點是：方案設計中提出多種方案，從可靠性、可實現性、綜合性能等進行方案比較，選擇方案。其構造特點是行走部件之間的傳動采用齒輪傳動和液壓傳動，通過油缸的伸縮來實現挖掘行走過程中的動力傳遞。差速器與回轉平臺鉸接技術設計中應考慮總體配置合理、安全；選材、加工方法和技術條件參閱相關技術資料；圖紙按照所設計的參數進行繪制。充分注意整機各子系統之間的相關性，力求整機性能的一致性和最優化性。從中可以看出整機作業能力有了很大的改進，不僅行走速度快，且整體挖掘機器重量輕，傳動平穩，作業效率高，結構緊湊。 關鍵詞：液壓挖掘機 行走裝置 減速器 指導教師簽名： Hydraulic excavator equipment design Student name:LeChenHui Class:0781052 Supervisor:XingPu Abstract：In this design, because the compact wheel running gear is high efficiency, by comparing the use of a tire to meet the design requirements of walking devices.According to design requirements, machine weight 11 tons; tire sizes 9.00-20; tire dynamic radius r = 0.491 meters. Excavator maximum traction P = 0.6 Weight; engine power N = 58.8KW, speed 2000r/min; pump maximum flow rate 2 × 100l/min; maximum working pressure of 21MPa. Maximum speed 31Km / h, designed to take full bridge driver.Upper turntable is the entire rotation, so it can be in a larger range.Because of the use of hydraulic mechanical transmission the entire machine performance can be improved.Compared with the traditional mechanical excavators, and its capacity to a lot of walking.The design of the main contents are: hydraulic excavator equipment design; assembly drawing general assembly drawings and sketches; power source selection and the determination of the parameters; running gear traction calculation; Transmission comparison and selection, determination and drive schemeTransmission of the technical design; planetary gear and parts and components of the design calculations, the main part strength check; drawn components and parts drawings, and assembly drawings, design calculations prepared statement. The design of the main features are: program design presented in a variety of programs, from the reliability, can be realized, for programs such as comprehensive performance comparison options.Its structure is characterized by walking between the drive components and hydraulic transmission with gear drive, stretching through the cylinder to achieve the excavation of the power during walking.Differential with the rotary platform articulated the overall technical design should be considered a reasonable allocation, security; selection, processing methods and criteria refer to the relevant technical information; drawings in accordance with the design parameters to draw.Full attention to machine the correlation between the various subsystems, and strive to overall performance of the consistency and optimization.Machine operation capability can be seen from a considerable improvement, not only walking speed, and overall mining machinery, light weight, smooth drive, high efficiency, compact structure. Keywords: Hydraulic walking device reducer Signature of Supervisor: