《注塑機保養手冊-臥式注塑機》由會員分享，可在線閱讀，更多相關《注塑機保養手冊-臥式注塑機（33頁珍藏版）》請在裝配圖網上搜索。

1、嘉興昌機械工業有限公司【注塑機保養手冊】1. 保養及檢查Maintenance and Examination日常保養及檢查機器壽命是非常重要,預防重于治療，然而對于機器而言，當然是保養重于修理了，射出成型機是一種高運轉的機器，一天可能接近 24 小時操作，若以一個月 25 個工作天而言，每一月累積 600 個操作小時，一年將達 7200 小時，幾乎是一般工具機4-5 倍長之操作時間。 保持良好的保養是減少及防止機器發生故障的最有效途徑。以下資料提供給用戶 , 使用機器時必須仔細閱讀, 給機器定期檢查保養及維護.It is important to maintain and examine t

2、he machine everyday. We are alwaystoldthatpreventionis betterthan cure,as well as machine, maintenance is betterthan repair. Injection molding machine as a kind of high operation machines, maywork near 24 hours in one day, ifitkeep working 25 days every month, then itwillaccumulate 600 operation hou

3、rs within a month,7200 hours in a year, which is 4-5times longer than general machine. Maintaining a good maintenance is the mosteffective way to reduce and prevent the malfunction of machine. The followinginformation is provided to user, and please keeps careful reading before using the machine as

4、well as examines and maintains regularly.1.1 清洗 Washing機器經過長時間使用后 , 所有滑動導桿、油缸的軸芯、滑面等會被沙塵等物質沾污 , 若不及時清理 , 滑動導桿、油缸軸芯及滑面會容易磨損 , 尤其對油缸軸芯油封為甚。保持清潔可防止由雜物引起磨損、堵塞、水份引起的銹蝕和及早發覺漏油情況。所以經常要清洗機器。請勿使用酒清、揮發性油、汽油、石油等制品擦拭人機屏幕，必須使用一般家庭擦試玻璃用清潔劑擦拭。Aftera long time using,allthe slidinglead-screw 、axis core of oilcylinde

5、r、sliding surface and so on will be stained by the sand flying in the air. If notcleaning in time,those placestalked above may be abradedeasily, especially theaxis core of oil cylinder. Keeping clean can avoid detritions、plugging causingby sundries and rustiness causing by water, and also easy to fi

6、nd the oil spill.Please use the general household glass cleaning agent to wipe the human-computerscreen, but not alcohol、volatile oil、gasoline 、 oil or other products.1.2 潤滑系統 Lubrication Systems有足夠潤滑可減少機件磨損, 必須經常加注潤滑油及油脂于機件如射臺導桿、鎖模導桿及有潤滑標識處 . 機臺 KS55C和 KS55T的注油點如下圖所示 :Ifthere s enough lubrication,i

7、tcan reduce mechanical detritions.Organ likeinjection stage lead-screw、clamping lead-screw and lubrication identificationmust be oftenadded oilor grease.Machine oilinjectionpointof KS55Cand KS55Tas shown in the following figure:射臺油缸射出組注黃油座臺油缸關模油缸嘉興昌機械有限公司潤滑示意圖標記 處數更改文件號簽字日期設 計標準化圖樣標記版本數量重量比例校 對審 定00

8、1530.1321:12審 核KS25T普通機KS25T-000工 藝日 期2014-06-26共頁第頁此處注入潤 滑 油此處注入此處注入潤 滑 油潤 滑 油射出部裝此處注入鎖模部裝潤 滑 油用戶必須注意以下幾點 :( 一) 潤滑油之選擇（1）耐高負載性（2）氧化穩定性（3）防銹性佳（4）適用 30# 40#（二）每個工作班的操作者必須檢查潤滑油喉能否向摩擦零件部位供油 , 不允許供油喉塞、脫落。（三）檢查油脂潤滑摩擦表面的潤滑油膜狀況, 不允許出現干摩擦 , 及時加注潤滑脂。User must pay attention to the following point:(一)Choice of

9、 lubrication oil(1) High load resistance(2)Oxidation stability(3)Good rustproofness(4)Apply to 30# 40#(二)Each work shift operator must check the oil throat whether it supply oil to friction parts, without oil throat plug or shed.(三)Check the condition of lubrication film on the grease lubricated sur

10、face, and dry friction is not allowed, filling grease in time.1.3 液壓系統 Hydraulic pressure system液壓油箱必須經常存有足夠液壓油, 可從裝置于油箱外之油尺檢查油位, 如果發覺油位低于要求 ,應及補充。Hydraulicfluidtank shouldbe oftenstoring withenoughhydraulicoil, andoillevelcanbeexaminedbyusingthedipstickwhich isfixedoutsidethe oilbox. If finding tha

11、t oil level is lower than requirement,it should be replenished in time., 應采用高質素之液壓油 , 液壓油在攝氏很多液壓系統毛病起源于已污染之液壓油30-50 度, 粘度在 150-225SUS或動動粘度 40-60厘澌最為適合。本司推薦使用46#液壓油 .Lots of errorsof hydraulicsystem originate from the pollutedhydraulicoil,so high qualityhydraulicoil isbetter.The suitablestateof thehy

12、draulicoilis in30-50 degree（temperature ）、150-225SUS（viscosity ）and 40-60ls (kinematicviscosity).Our company recommends #46 of hydraulic oil.用戶亦須定期檢查液壓油，若果需要更換液壓油，把原有液壓油抽掉，清洗油箱后，再加注全新液壓油于油箱內（新舊液壓油不能混合）, 同時清洗油篩。Users also should check the hydraulicoilregularly. If it needs to renewalthe hydraulic oil

13、, firstly, take out the original hydraulic oil and wash thetank. And then in pour the new hydraulic oil (oil and new hydraulic oil can notbe mixed together.), wash the oil screen at the same time.機器在正常運作時，液壓系統溫度不能超過攝氏55 度。在超過情況下工作，液壓系統會產生以下現象：When the machine works regularly, the temperature of hydr

14、aulic pressure system can not overtake 55 degree. If it is exceeded, the hydraulic pressure system will come with the follow phenomenon:（一）液壓油氧化加速，提前變質。Oxidation of hydraulic oil is accelerated, and deteriorate in advance.（二）粘度降低導致油泵及其他閥體受損.Viscosity reducing cause damage to pumps and other parts.（三

15、）油封加快老化。Oil seal accelerate to ageing.若發覺 If find that（一）液壓油出泡沫If hydraulic oil bubble,（ 1）應檢查油泵吸油管的密封性。Check the leak-tightness of the oil pump suction pipe.（ 2）應檢查液壓油是否充足。Check the hydraulic oil whether it is sufficient.（ 3）應檢查回油管是否沉入液壓油內。Check back the oil tube whether it is sinking into the hydr

16、aulic oil.（二） 液壓油呈懸浮狀態白色I(xiàn)f hydraulic oil appear in white suspended state,（ 1） 應檢查油箱密封性，可能由于空氣潮濕，空氣中水氛進入液壓油內。Check the leak-tightness of the oil tank whether liquid watercontent in the air get into the hydraulic oil.（ 2） 應檢查熱閃換器水管是否損壞導致冷卻水混入液壓系統內。Check the Hot Flash Converter water pipe whether it is

17、 damage resulting in cooling water mixing into the hydraulic system.1.4 液壓泵及液壓閥Hydraulic pump and hydraulic valve由于液壓泵及液壓閥結構精密及復雜, 維修保養必須由技術人員處理。裝拆時，要加倍小心以免損壞零件。Due to the precision and complex of hydraulic pump and hydraulic valve structures, maintenance and repair must be dealt with by the technic

18、al staff. When assemble and disassemble, be careful so as not to damage the parts.s1.5 油隔 Grease trap油隔功能是把液壓油被油泵吸入前經過油隔而過濾異物。必須經常檢查油隔，若油隔嚴重受污染油泵吸油管產生真空導致油泵損壞。The function of the grease trap is that filters the foreign matter before hydraulic oil being sucked by the oil pump. Check the grease trap u

19、sually, andif the grease trap is polluted seriously, the oil pump suction pipe will emerge vacuum causing the oil pump damaged.1.6油封 Grease seal所有密封填充圈是裝于油缸及閥體上, 當密封圈損壞時 , 會影響機器工作性能 , 甚至泄油。需要時，應及早更換損壞之密填封圈。Allsealed filledcircles are installedon the oiltank and valve body, andwhen the sealed circles

20、is damaged, itwillaffect theperformance of the machineand even oil drainage.1.7電路控制 Circuit control在正常運作時 , 防止水及其他雜物進入電箱, 電箱門應緊密關閉 . 遇到電路故障時應由合資格的工作人員負責維修。臺電部份聯接螺絲應緊固，防止因松脫而導致危險。經常檢查電箱溫度不能太高，防止影響電子零件的正常運作。同時定期檢查安全門電器互鎖及行程咭掣以免發生意外。In normal operation, prevent water and other debris getting box and th

21、e door of the electric box should be closed tightly.intoWhenitthe electricencountersa circuit fault, eligible staff should be responsible for maintenance.1.8 電熱 Electric heat應經常檢進電熱 . 電熱不正常會產生注塑總是導致產品質素低.Check the electric heat regularly. Abnormal electric heat can produce plastic injection resultin

22、g in a low quality of product.（一）檢查積各段電熱是否正常。Check each part of electric heat whether it is normal.（二）檢查溫度控制狀態。Check the control status of the temperature.（三）檢查控溫線端與熔膠筒接觸狀況。Check the contact status between temperature control terminal and melt adhesive cylinder.1.9熔膠筒及螺桿更換聯結Melt adhesive cylinder an

23、d screw replacing the coupling assembly（一）對射咀進行拆除或移開，必須先淺放掉料管內部的塑料產生的壓力。Beforedismantlingor removing the shoot mouth, pressureproduced by the plasticinsidethe material pipe should be unhanded lightly.因為有時溫度會對封閉式料管內部的塑膠產生化學反應，并于料管內產爆炸性的壓力。Because that sometimes temperature can lead to that plastic ta

24、ke place chemical reactions and cause a explosive pressure inside the closed material tube.將料管的溫度降下及降低內部的壓力，按下松退鍵讓螺桿向后退。Pressing the loose back key and making the screw back can lower the temperature and pressure inside the material tube.（二）塑膠于料管內加熱時間太長是相當?shù)奈ｋU的，因為長時間的對塑膠加溫產生的毒的氣體，并經由射嘴噴出來。It is dange

25、rous to heat the plastic cement inside the material tube too long time.Because of that long time heating the plastic will produce the toxic gases and spraying out from the shoot mouth.（三）料咀跑入異物時，不可以加高溫度或高壓力將體更擠出來。If there s some foreign matter come from the material mouth, do not rise up the tempera

26、ture and pressure to squeeze it out strongly.必須關掉電源并將漏斗內時，然后再將異物清除。Turn off the power and use a funnel to clear the foreign matter.（四）當硬物掉入送料漏斗時， ，要取出時必須相當?shù)男⌒?。If the hard objects fall down into the feed funnel, pay more attention when take it out.（五）拆下料管的護蓋前必須先確認關閉總電源開關。Be sure the main power is off

27、 before removing the material tube s cover.（六）嚴禁將潤滑油涂抹于射出螺桿、料管、電熱片上。Lubricant applied to injection screw、 material tube、electric flake is forbidden.（七）清洗或更換零件時，必須拆除熔膠筒、螺桿及止逆閥等零件。先選擇手動方式。Washor change the parts, must dismantle melt adhesive cylinder 、screw and lock check gate first. Select manually f

28、irst.按以下步驟更換熔膠筒：Replacing the melt adhesive cylinder according to the following steps:1) 關閉料斗閘板，采用手動或自動清洗功能把剩余塑料從熔膠筒打出。Close the hopper gate, and choose manual or automatic cleaning function to whip out the remaining plastic from the melt adhesive cylinder.2) 操作射臺至最后位置。Transfer operation injection s

29、tage to final position.3) 關掉電源，拆除電熱圈。Turn off the power, removal the electric circle.4) 松掉熔膠筒，鎖緊螺母。Loose the melt adhesive cylinder, and lock the nut tightly.5) 松掉螺桿端與傳動軸之聯結組件。Loose the coupling components between screw terminal and drive shaft.6) 采用車間行車把熔膠筒穩固吊著，后把熔膠筒從射臺拉出。Use a workshop bridge cran

30、e to hang the melt adhesive cylinder stably, and then pull it out from the injection stage.按以下步驟更換螺桿：Replacing the screw according to the following steps:1) 關閉料斗閘板，采用手動或自動清洗功能把剩余塑料從熔膠筒打出。Close the hopper gate, and choose manual or automatic cleaning function to whip out the remaining plastic from th

31、e melt adhesive cylinder.2) 操作射出臺至最后位置。Transfer operation injection stage to final position.3) 逆時針方向搖擺射臺（先松掉或拆除有關之螺絲或另件） 。Swingthe injectionstage in a counterclockwisedirection(loose or removethe relevant screws or others first).4) 松掉螺桿端與傳動軸之聯結。Loose the coupling components between screw terminal an

32、d drive shaft.5) 拆除射咀及射咀法蘭。Remove the shooting mouth and shooting mouth flange.6) 操作螺桿“倒索“動作把螺桿端與傳動軸脫離，必要時，用木方枕著螺桿端與傳動軸之間。Use the“fall cable ” movement of the operation screw to separate the screw terminal and drive shaft. If necessary, pillow with a squared timber between screw terminal and drive s

33、haft.7) 操作射膠動作把螺桿推出。Pull the screw out by the operation injection action.注意 : 為安全起見 , 把射膠壓力及速度數值調低, 由于熔膠筒已被加熱 , 拆除時小心被燙傷。Note: for security, lower the numerical of injection pressure and speed. As the melt adhesive cylinder is heated, be careful when dismantle.本機螺桿前端裝有標準型之止逆閥組件，止逆閥組件采用左牙螺紋與螺桿連接。當螺桿轉

34、動時不容易把止逆閥松出，松脫時請留意旋向 .There is a standard lock check gate which is use the left tooth screw thread to connect with screw on this machine. When turning around the screw, if it is not easy to loose the lock check gate. Pay attention to the turn when doffing.1.10 定期檢查 Regular checking（一）每天檢查一次Check it

35、once a day.（ 1）當機器運作時，檢測電馬達、油泵、油管及油閥發出聲音及震動狀況。When the machine is moving, check the sound and vibration condition of electric motors 、 pump、 oil pipe and oil discharge valve.（ 2）檢查系統壓力及油溫，若溫度過高，檢杳冷卻系統部份。Check the system pressure and temperature. If the temperature is too high, check the cooling syst

36、em, too.（ 3）觀察液壓系統之管道接口、閥體、法蘭等有否泄油。Observe the pipe s interfaces 、valve 、 flange of the hydraulic system if there s a oil leakage.（ 4）觀察冷卻系統管道有否漏水。Observe the cooling system if theres a water leakage.（ 5）檢查安全裝置、緊急停止按扭及指示燈狀況。Check the safety device、emergency stop button and pilot lamp.（ 6）檢查螺絲、螺母等緊固狀

37、況。Check the screw、 nut.（ 7）檢查潤滑系統。Check the lubrication systems.（二）每星期檢查一次Check it once a week:（ 1）檢查加注潤滑點。Check it lubrication points.（ 2）檢查電路如電熱圈、控?zé)峋€、行程咭掣等按線狀況。Checkthe circuit s wiringstate,likeelectrichotline、travel cards for appliances and so on.heatingloop 、control（ 3）緊固可能松脫之螺絲、螺母及聯結法蘭。Fixture

38、 those may loosened screw、nut and fitting flange.（ 4）清洗機器上所有滑動之機件，以免被沙塵覆蓋容易受損。Wash all the slidingable organs of the machine, so that it will not be easy to damage caused by the dust.（三）每月檢查一次Check it once a month:（ 1）檢查安裝裝置Check the install device.（ 2）檢查閥體之線圈是否松脫。Check the coil of the valve whether

39、 it is loosened.（ 3）檢查液壓油是否保持良好質素。Check the hydraulic fluid whether it keeps a good situation.（ 4）更換已磨損之機件。Change the wearer.（四）每年檢查一次Check it once a year:（ 1）更換已磨損之機件。Change the wearer.（ 2）檢查系統壓力，必要時重新調節。Check the system pressure, and adjust again if necessary.（ 3）檢查熔膠轉動軸承狀況，加注潤滑油脂。Check the condit

40、ion of melt spinning bearings, and add some grease lubricant.（ 4）清洗熱交換器。Wash the heat exchanger.1.11 機器的儲存 Keep of machine如果機器長期不生產運作，請在檢查機器之后用保護膜罩好，以防雜塵物進入。Ifthe machine doesn t work for a long time,please use a protectivefirmcoverthe machine before checking, in case of the dust going into.2. 常見故障及

41、排除方法Common Troubles and Excluded Solutions2.1. 報警及排除 Alarm and exclude常見報警原因及排除方法common alarmCause and excluded solutions當頂針兩個限們開關同時壓合 (X013、 x014 同時亮：查看兩個接線點處是否有短路 S，行程開關們置是否松動或不恰當 )脫模失敗Whentwo limit switch of the centrepress at the sametimeFail to knockout(X013、 x014 lightsimultaneously:Check whet

42、her there sa short circuitS at the connection, and limit switch isloosed or improper.機械手失敗機械手操作中，機械手未能復位（功能頁面機械手選擇使用）When the manipulator is operating, it failed to resetFail in manipulator(manipulator select function page )射嘴護罩打開射膠安全門（ X514）未關Open the injectionInjection safety doors (X514) is close

43、d.mouth cover自動過程中，在熔膠計時內未能完成熔膠動作：熔膠時間、行熔膠未定時完成程的設定是否正確，料筒時有無料，熔膠壓力、流量是否夠大In the process of automatically, failed to complete theMelt adhesive is notmelt in the melttiming action: whether the melt timeandscheduled to completetrip setting is correct and if theres material in thebarrel; whether melt p

44、ressure and flow is large enough.開鎖模計時內，未能完成開模動作： 開鎖模時間設定是否正確，開模未定時完成開模壓力、流量是否夠大，此時循環不能繼續Opening mould is notFailed to complete the opening mould action in time:scheduled to completewhether the setting time is correct and the pressure、flow is large enough; cycling cannot continue開模計時內，未能完成鎖模動作：開鎖模時間

45、設定是否正確，關模未到定位鎖模壓力、流量是否夠大Closing mould doesn tFailed to complete the closing mould action in time:reach positionwhether the setting time is correct and the pressure、flow is large enough; cycling cannot continue開模未到定位作頂針動作時，開模終止行程（開模二慢）未到或限位咭制（X013）未壓合Opening mould doesn tIn centre action, opening mou

46、ld end the route isnot reachreach positionor limit cards (X013) are not pressed.座退未到定位作滑模或轉盤動作時，座退終止開關（X007）未壓合Seat back doesntWhendo sliding or turntableaction,seat back end switchreach position(X007) is not pressed.滑模未到定位作鎖模、頂針動作時，滑模終止開關（X403、X404）未壓合Sliding mould doesntWhen do closing mould and c

47、entre action, sliding mouldreach positionend switch (X403 、X404)is not pressed.頂退未到定位作鎖模、滑?；蜣D(zhuǎn)盤動作時，頂退終止開關（ X011、X013）未壓合Drift doesn t reachWhen do the closing mould 、 sliding mould and turntablepositionaction, drift end switch（X011、X013） is not pressed.定位上未到定位作鎖模、頂針動作時，定位上終止開關（X516）未壓合Position up doe

48、sn tWhendo the closingmould and centreaction, positionupreach positionend switch （X516） is not pressed.定位下未到定位作滑?；蜣D(zhuǎn)盤動作時，定位下終止開關（X517）未壓合Position down doesn tWhendo the slidingmould and turntable action,positionreach positiondown end switch （X517） is not pressed.開模總數已到實際開模次數到達時間頁面內“開模限數”的設定值Reach the

49、 openingmouldReal opening mould times reach the setting point on thetotalitytime table.潤滑油位低潤滑油箱內的潤滑油低于潤滑油位開關（X405）Low lubrication oilLubrication oil in the tank is lower than the oil levellevelswitch （X405）料筒溫度太高料筒的實際溫度高于設定溫度加上高溫偏差Material barrelsReal temperature of material barrel is higher than t

50、hetemperature is toohighdesign temperature pulsing the deviation料筒的實際溫度低于設定溫度減去低溫偏差， 此時不能進行射料筒溫度太低膠、熔膠、抽膠動作Real temperature of material barrel is lower than theMaterial barrelsdesign temperaturecuttingthedeviation,andnotemperature is too lowinjection 、melting and taking out the glue action thismomen

51、t.2.2. 故障及排除Failures and Trouble Exclude故障現象原因及排除方法Fault symptomCause and excluded solutions1、檢查開關電源保險管系統不上電Check the protector tube of power switch2、檢查開關電源各路輸出是否正常System can not reachCheck the output line of power switchthe power3、檢查主機板保險管Check the protector tube of mainboard.1、檢查各動作輸出條作是否滿足Check w

52、hether allthe output action is reach the condition2、檢查外部相關行程開關是否有壞Check whether relevant route switch outside is broken.I/Olwg 出現不正常3、檢查輸入輸出檢測頁面相應點是否輸出，如有輸出則頁面更改輸入輸出點，相應調換輸入輸出點I/Olwg is not normalCheckwhetherthe input/outputdetectionpage scorresponding points is output, if output, then change the ou

53、tput and input point.4、通知生產廠Inform the producer.1、對比度是否調好，調對比度Contrast might not be adjusting well.2、面板后蓋的穩壓管7805 是否插好Voltage-stabilizingtube of thepanel s back cover7805有背光無字might not be plugging well.3、程序是否插好Back light withoutProcedure might not be plugging well.words4、液晶模塊與顯示板的連線是否插好The linebetwe

54、en liquid crystalmodule and displaypanelmight not be plugging well.5、通知生產廠Inform the producer.1、連結線是否松動，把連結線螺絲旋緊The line might be loosed. Screw the screws lightly.2、電源問題，查看電源盒 +12V，+24V1A是否正常有字無背光Power problems. Check the power box +12V ， +24V1AWords without back3、顯示板與鍵盤板，液晶模塊的背光線是否插好lightdisplaypan

55、el and keyboard panel 、the back light of liquidcrystal module might not be plugging well.4、通知生產廠Inform the producer.1、聯結線是否松動，把聯結線螺絲旋緊The line might be loosed. Screw the screws lightly.顯示閃動2、電源問題，面板后蓋的穩壓管7805 沒插好或壞Display flashingtube of thePower problems. Check the Voltage-stabilizingpanel s back c

56、over 7805.3、外圍供電電 220VACA或 380VAC）低或不穩Check whether the external power supply 220VACA或 380VAC is too low or unstable.4、通知生產廠Inform the producer.1、聯結松動，把聯結線螺絲旋緊The line might be loosed. Screw the screws lightly.2、電源問題，查看電源盒電源是否正常： 板面后蓋的穩壓管 7805無顯示無背光是否插好 , 顯示板燈是否亮No display and no backPower problems. Check the power box: Voltage-stabilizinglighttube of the panel s back cover 7805; whether the lightof display panel is light.3、通知生產廠Inform the producer.1、電池電壓低（一般不能低于3V）換電池Low voltage of battery (generallydon t lessthan3V );記憶丟失change the battery.2、記憶塊壞（ 256）壞Memory lossMemory block (256) is brok