喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== 喜歡就充值下載吧。。資源目錄里展示的文件全都有，，請放心下載，，有疑問咨詢QQ:414951605或者1304139763 ======================== ..大學.. 畢業論文（設計）任務書 論文（設計）題目： 摩托車液壓減震器設計 學號： .. 姓名： .. 專業： 機械設計制造及其自動化 指導教師： ..教授 系主任： 一、主要內容及基本要求 (1)基本掌握摩托車液壓減震器的組成及功能。 (2)掌握摩托車液壓減震器的基本知識。 (3)分析液壓減震器的原理，繪制原理圖。 (4)對液壓減震器的有關參數進行計算，并繪制裝配圖，若干零件圖。 (5)翻譯一份有關本課題的3000字以上中英文文獻資料。 (6)設計說明書8000字以上。 二、重點研究的問題 分析液壓減震器的原理。 三、進度安排 序號 各階段完成的內容 完成時間 1 資料檢索、查詢 第1至2周 2 總體方案構思設計 第3至4周 3 掌握減震器原理 第5至7周 4 完成減震器的相關參數設計 第8至12周 5 畢業論文撰寫和編輯 第13至14周 6 交畢業設計說明書和圖紙，答辯準備 第15周 四、應收集的資料及主要參考文獻 [1]陳守慶.摩托車減震器行業的現狀及發展策略[J]. 摩托車技術，2003，5：32-38 [2]張冰蔚，單春賢.摩托車減震器示功圖測試與分析[J]. 華東船舶工業學院學報， 2000，14(4)：59-62 [3]田茹會, 王鐘羨. 改進的遺傳算法在減震器優化中的應用[J]. 機械工程師，2006.(03) [4]摩托車技術[M].北京,機械工業出版社,2005 [5]單春賢,張冰蔚,陸　勇.摩托車前減震器阻尼特性數學模型的建立 江蘇理工大學學報，2001，22(5):26-32 [6]單春賢,仲敏波,吉恒松,邵　霞.摩托車筒式減震器液壓阻尼特性的模擬與仿真江蘇理工大學學報,2007,28(1):26-34 [7]姜水生,文華,劉越琪.減震器特性的統計模擬研究[J].南昌大學學報，1999,21(2):9-29 [8]汪通悅.摩托車減震器動力特性研究[J].現代機械，2000，4：56-60 [9]劉愛紅 ,茹小元.摩托車減震器總成靜載荷特性分析[J].摩托車技術，2005，4：11-14 [10]劉愛紅,賀陽.摩托車減震器阻力_速度特性曲線常用種類及應用[J]. 摩托車技術,2007,6:65-71 [11]楊基忠,俞大衛,葉全勇.減振器振動系統穩定性分析與研究[J].兵工學報，2000,77(1):43-56 [12]周　臻,何正琛.淺析摩托車減震器的_軟_與_硬_[J].成都航空職業技術學院學報，2004，60(3):79-83 [13]馬震來. 汽車液壓減震器參數優化設計[J]，2004.(3) [14]成大先，王德夫，姬奎生，韓學銓，姜勇，李長順. 機械設計手冊[M]. 工業出版社，2002.(3) ..大學.. 畢業論文（設計）評閱表 學號 .. 姓名 .. 專業 機械設計制造及其自動化 畢業論文（設計）題目： 摩托車液壓減震器設計 評價項目 評 價 內 容 選題 1.是否符合培養目標，體現學科、專業特點和教學計劃的基本要求，達到綜合訓練的目的； 2.難度、份量是否適當； 3.是否與生產、科研、社會等實際相結合。 能力 1.是否有查閱文獻、綜合歸納資料的能力； 2.是否有綜合運用知識的能力； 3.是否具備研究方案的設計能力、研究方法和手段的運用能力； 4.是否具備一定的外文與計算機應用能力； 5.工科是否有經濟分析能力。 論文 （設計）質量 1.立論是否正確，論述是否充分，結構是否嚴謹合理；實驗是否正確，設計、計算、分析處理是否科學；技術用語是否準確，符號是否統一，圖表圖紙是否完備、整潔、正確，引文是否規范； 2.文字是否通順，有無觀點提煉，綜合概括能力如何； 3.有無理論價值或實際應用價值，有無創新之處。 綜 合 評 價 選題較具時代性和現實性。全文結構安排合理。觀點表達基本準確。全文內容緊扣機械設計專業要求來寫，充分體現出機械設計專業特色。查閱的相關資料較多。但不足之處主要是屬于自己創新的東西還不多。 總體上符合畢業論文要求。 評閱人： 2012年5月 日 ..大學.. 畢業論文（設計）鑒定意見 學號： .. 姓名： .. 專業： 機械設計制造及其自動化 畢業論文（設計說明書） 36 頁 圖 表 張 論文（設計）題目： 摩托車液壓減震器設計 內容提要： 本課題是對摩托車減震器進行系統設計，主要完成以下兩個內容的研究： 1：摩托車減震器的工作原理，繪制原理圖 2：對摩托車減震器的結構進行分析設計，對有關參數進行運算論證。 指導教師評語 ..同學于本次畢業設計過程中積極查找相關文獻、資料，按時完成老師要求，多與同學交流，雖水平仍有待提高，但總體表現良好，同意進行答辯。 指導教師： 年 月 日 答辯簡要情況及評語 答辯小組組長： 年 月 日 答辯委員會意見 答辯委員會主任： 年 月 日 6 外文翻譯-原文部分 SHOCK ABSORBER 【Introduction】 Shock Absorber Damper (Vibration Damper), shock absorber spring is mainly used to suppress rebound after the shock-absorbing shocks when the shocks from the road. After uneven pavement, while shock-absorbing spring can filter road vibration, but the spring itself will have reciprocating motion, which is used to control this kind of shock absorber spring jumping.Shock absorber is too soft, the body will be jumping up and down, shock absorbers too hard or too much resistance will impede the normal work of the spring. Suspension system on the conversion process, the hardware and hardware to the shock absorber of the spring with, and the spring hardness is closely related with the weight, so heavier vehicles generally use the shock absorber hard.David cited the crankshaft and connected devices, used to counter the crankshaft torsional vibration (that is, by crank the ignition cylinder and twist the impact of the phenomenon). 【Classification】 Shock Absorber From the shock absorber damping materials have divided this point there are two types of hydraulic and pneumatic, as well as a variable-damping shock absorber. Now the shock absorbers are: 1. Rubber shock absorber; 2.Spring shock absorber; 3. air type shock absorber; 4. Oil air dampers; 5. the whole oil type shock absorbers. 【The structure of shock absorber】 The structure of shock absorber piston rod with a tube inserted in the tube-in-full of oil. Orifice Pistons have made have been separated from the piston space of two parts oil to each other.With viscous damping is through the oil produced Orifice, Orifice smaller, the greater the damping force, the greater the viscosity of oil, the greater the damping force. Orifice size if the same work faster when the shock absorber, the damping influence of the General Assembly had to absorb shocks.As a result, the exit of Orifice to set up a disk-shaped valve spring, when the pressure change when the top valve was opened, Orifice opening larger, smaller damping. As the piston is a two-way movement, so both sides are equipped with piston valve spring, respectively, called the compression valve and valve done. Shock absorber according to their structure can be divided into double and single tube-type. Binocular-type shock absorber means there are both inside and outside the two cylinders, pistons, including tube-in-movement, as a result of the entry and out piston rod, the volume of oil inside the cylinder increases with the contraction, it should be exchanged with the outer tube to maintain balance within the cylinder oil. So have a double shock absorber in the four-valve, that is, in addition to the above-mentioned two throttle piston, there are both inside and outside the tube in a complete exchange between the valve and the flow compensation valve. Compared with the double-type, single tube-type shock absorber simple structure, a reduction of a valve system. In the lower part of cylinder equipped with a floating piston, (the so-called floating piston rod means that there is no control over their movements), the following in the floating piston to form a sealed chamber, there are high-pressure nitrogen charge. As a result of the above-mentioned piston rod into and out of oil caused by a change in liquid height of floating through the floating piston to automatically adapt.In addition to the above-mentioned two types of shock absorber, there are adjustable shock absorber resistance. It can be changed through an external operation to the size of Orifice. Recently, the car will be electronically controlled shock absorber as a standard-type equipment, traveling through the sensor detection, and by a computer to calculate the best damping force, so that the damping force shock absorber to adjust automatically the work of institutions. The working principle of automobile shock absorbers: Suspension system components due to elastic vibration generated by the impact, in order to improve vehicle ride comfort, suspension elastic element in parallel with the installation of shock absorber for the attenuation of vibration, automotive suspension systems are used in hydraulic shock absorber damping , and its working principle is that when the frame (or body) and the inter-axle relative motion by vibration occur, the shock absorber piston moved up and down inside, shock absorber oil cavity will be repeated from one chamber to go through the various Another pore cavity flows.At this point hole wall and the friction between oil and oil of the internal friction between the molecules formed on the vibration damping force, so that vehicle vibration energy into heat oil, and then distributed by the shock absorber to absorb the atmosphere. Channel cross-section and in the oil change and other factors, the damping force with the frame and axle (or wheel) the relative velocity between the increase or decrease, and the viscosity of the oil. Shock absorber components and flexibility with ease to assume the task of the impact and vibration, the damping force is too large, flexible suspension will deteriorate, and even damage to shock absorber connector. Hence, the flexibility to adjust shock absorber components and this contradiction. (1) in the compression stroke (near the axle and frame each other), a smaller shock absorber damping force in order to give full play to the role of elastic elements of flexibility, ease the impact. At this time, play a major role in elastic elements. (2) trip done in suspension (axle and frame away from each other), shock absorber damping force should be large and rapid damping. (3) When the axle (or wheel) and the relative velocity between the axle is too large, the request can automatically increase the shock absorber fluid flow, so that damping force is always maintained within certain limits in order to avoid to put too much impact load. In the automotive suspension system is widely used in Shock Absorber, and done in the compression and all-day trip called the two-way play the role of the role of vibration-type shock absorber, as well as the use of the new shock absorber, which includes inflatable adjustable shock absorber and shock absorber resistance. The role of two-way Shock Absorber Description working principle. In the compression stroke, the wheels moved closer to the body means a motor vehicle, shock absorber by compression, when the shock absorber piston within 3 down. Under the piston chamber of volume reduction, oil rise, the flow of oil through the valve 8 into the piston chamber above (superior). On the piston rod cavity was taken up as part of a space, thus increasing the cavity volume is less than the inferior vena cava to reduce the volume of oil was on the compression valve 6 open, flows back to storage tank 5. These valves to form a suspension of oil-saving campaign by the compression of the damping force.Shock absorber in the journey done, the wheel is equivalent to far away from the body, the shock absorber by stretching. Shock absorber when the piston up. Increase the hydraulic piston chamber, the flow valve 8 closed, the cavity of the oil done away inferior vena cava inflow valve 4. Due to the existence of rod, since the cavity is not sufficient oil flow to the inferior vena cava with the increase in volume, under the instigation of a vacuum chamber generated, when the oil tanks in the open compensation valve 7 into the inferior vena supplement. As a result of these throttling valve in the role of suspension damping done to play the role of exercise. Done as a result of valve spring stiffness and pre-compression force greater than the design of the valve, in the same pressure, the valves done and the corresponding slot of the channel Changtong area contains less than the sum of the corresponding valves and compression Changtong channel cross-sectional area of the sum of the gap. This has done the trip have a shock absorber damping force is greater than the compression stroke damping force to the requirements of the rapid damping. Shock Absorber, prospects for the development of automotive components Auto parts as the basis of the automobile industry, the automotive industry is continuing to support the healthy development of the necessary factors. Especially now, the automotive industry is dynamic, full autonomy to carry out development and innovation, but also needs a strong support system as the parts. Own brand vehicles and technological innovation as the basis of the need for spare parts, parts of the independent innovation and development of automotive industry have a strong driving force, they are interactive, interaction, and there is no vehicle of their own brand, a powerful system components R & D innovation capability difficult to burst, there is no strong support system components, and independent brands forced to do difficult masterpiece. 2006 January to December, China total auto parts and accessories manufacturers to achieve a total industrial output value of 539,704,996 thousand, representing 34.35 percent increase over the same period the previous year; to achieve a total sales income 527,234,933 thousand, representing 34.71 percent increase over the same period the previous year; achieve a cumulative total of 32,605,652 thousand dollars profit, than the 46.79 percent increase over the same period the previous year; As of the end of December 2006, the entire industry the number of above-scale enterprises for 6142. 2007 January to November, China total auto parts and accessories manufacturers to achieve a total industrial output value of 683,525,503 thousand dollars more than the same period last year increased by 37.34%; to achieve a total sales income 663,529,269 thousand, representing an increase of 37.45 over the same period last year %; the realization of the cumulative total amount of 48,487,363 thousand dollars profit last year, an increase of 68.61 percent over the same period; as at the end of November 2007, the entire industry the number of above-scale enterprises for 7171. 2008 January to November, China auto parts and accessories manufacturing industry realized a total industrial output value of 865,835,708 thousand dollars more than the same period last year increased by 25.62%; to achieve a total sales income 837,913,601 thousand dollars more than the same period last year increased by 24.12% ; the realization of the cumulative total amount of 53,876,595 thousand dollars profit last year, an increase of 15.92 percent over the same period; as at the end of November 2008, the entire industry the number of above-scale enterprises for 8303. Auto parts manufacturers from the automotive parts business and the formation of specialized groups, is becoming a trend of globalization. The world leading automotive and auto parts enterprises, almost all in China, established a joint venture or wholly foreign owned enterprises, technology joint ventures have been more than 1000. Domestic scientific and technological content of a number of high-effective, large-scale enterprises of motor vehicles and parts have grown up gradually. International automotive industry with the introduction of parts of "globalization of procurement," Strategy and the implementation of the international cross-border car localization strategy, the domestic market will be huge gaps in parts accessories. By 2010, China domestic auto parts production will reach 7000 billion . At present, although the overall decline in the global economy, but the last four to five years in accordance with the actual procurement practice, the fruits of China procurement of a large number of companies is not as predictable as optimistic, almost 80% of companies do not achieve their purchasing and procurement costs down目標. With the revaluation of the RMB and the export tax rebate rate of decline, China is facing even greater pressure on the procurement, international buyers will be looking at the same time has been transferred to Vietnam, India, Thailand, Australia and other countries and regions. It appears from the above, China auto parts industry in the current financial crisis will accelerate the growth. 外文翻譯—譯文部分 減震器 【減震器簡介】 　　減震器(Vibration Damper) ，減震器主要用來抑制彈簧吸震后反彈時的震蕩及來自路面的沖擊。在經過不平路面時，雖然吸震彈簧可以過濾路面的震動，但彈簧自身還會有往復運動，而減震器就是用來抑制這種彈簧跳躍的。減震器太軟，車身就會上下跳躍，減震器太硬就會帶來太大的阻力，妨礙彈簧正常工作。在關于懸掛系統的改裝過程中，硬的減震器要與硬的彈簧相搭配，而彈簧的硬度又與車重息息相關，因此較重的車一般采用較硬的減震器。與引震曲軸相接的裝置，用來抗衡曲軸的扭轉振動(即曲軸受汽缸點火的沖擊力而扭動的現象)。 【減震器的分類】 　　減震器從產生阻尼的材料這個角度劃分主要有液壓和充氣兩種，還有一種可變阻尼的減震器. 　　現在使用的減震器有： 　　1.橡皮減震器； 　　2.彈簧減震器； 　　3.空氣式減震器； 　　4.油液空氣式減震器； 5.全油液式減震器。 【減震器的結構】 　　減振器的結構是帶有活塞的活塞桿插入筒內，在筒中充滿油?；钊嫌泄?jié)流孔，使得被活塞分隔出來的兩部分空間中的油可以互相補充。阻尼就是在具有粘性的油通過節流孔時產生的，節流孔越小，阻尼力越大，油的黏度越大，阻尼力越大。如果節流孔大小不變，當減振器工作速度快時，阻尼過大會影響對沖擊的吸收。因此，在節流孔的出口處設置一個圓盤狀的板簧閥門，當壓力變大時，閥門被頂開，節流孔開度變大，阻尼變小。由于活塞是雙向運動的，所以在活塞的兩側都裝有板簧閥門，分別叫做壓縮閥和伸張閥。 　　減振器按其結構可分為雙筒式和單筒式。雙筒式是指減振器有內外兩個筒，活塞在內筒中運動，由于活塞桿的進入與抽出，內筒中油的體積隨之增大與收縮，因此要通過與外筒進行交換來維持內筒中油的平衡。所以雙筒減振器中要有四個閥，即除了上面提到的活塞上的兩個節流閥外，還有裝在內外筒之間的完成交換作用的流通閥和補償閥。 　　與雙筒式相比，單筒式減振器結構簡單，減少了一套閥門系統。它在缸筒的下部裝有一個浮動活塞，(所謂浮動即指沒有活塞桿控制其運動)，在浮動活塞的下面形成一個密閉的氣室，充有高壓氮氣。上面提到的由于活塞桿進出油液而造成的液面高度變化就通過浮動活塞的浮動來自動適應之。除了上面所述兩種減振器外，還有阻力可調式減振器。它可通過外部操作來改變節流孔的大小。最近的汽車將電子控制式減振器作為標準裝備，通過傳感器檢測行駛狀態，由計算機計算出最佳阻尼力，使減振器上的阻尼力調整機構自動工作。 　　汽車減震器的工作原理: 　　懸架系統中由于彈性元件受沖擊產生振動，為改善汽車行駛平順性，懸架中與彈性元件并聯安裝減振器，為衰減振動，汽車懸架系統中采用減振器多是液力減振器，其工作原理是當車架（或車身）和車橋間受振動出現相對運動時，減振器內的活塞上下移動，減振器腔內的油液便反復地從一個腔經過不同的孔隙流入另一個腔內。此時孔壁與油液間的摩擦和油液分子間的內摩擦對振動形成阻尼力，使汽車振動能量轉化為油液熱能，再由減振器吸收散發到大氣中。在油液通道截面和等因素不變時，阻尼力隨車架與車橋（或車輪）之間的相對運動速度增減，并與油液粘度有關。 　　減振器與彈性元件承擔著緩沖擊和減振的任務，阻尼力過大，將使懸架彈性變壞，甚至使減振器連接件損壞。因面要調節彈性元件和減振器這一矛盾。 　　(1) 在壓縮行程（車橋和車架相互靠近），減振器阻尼力較小，以便充分發揮彈性元件的彈性作用，緩和沖擊。這時，彈性元件起主要作用。 　　(2) 在懸架伸張行程中（車橋和車架相互遠離），減振器阻尼力應大，迅速減振。 　　(3) 當車橋（或車輪）與車橋間的相對速度過大時，要求減振器能自動加大液流量，使阻尼力始終保持在一定限度之內，以避免承受過大的沖擊載荷。 　　在汽車懸架系統中廣泛采用的是筒式減振器，且在壓縮和伸張行程中均能起減振作用叫雙向作用式減振器，還有采用新式減振器，它包括充氣式減振器和阻力可調式減振器。 　　雙向作用筒式減振器工作原理說明。在壓縮行程時，指汽車車輪移近車身，減振器受壓縮，此時減振器內活塞3向下移動。活塞下腔室的容積減少，油壓升高，油液流經流通閥8流到活塞上面的腔室（上腔）。上腔被活塞桿1占去了一部分空間，因而上腔增加的容積小于下腔減小的容積，一部分油液于是就推開壓縮閥6，流回貯油缸5。這些閥對油的節約形成懸架受壓縮運動的阻尼力。減振器在伸張行程時，車輪相當于遠離車身，減振器受拉伸。這時減振器的活塞向上移動。活塞上腔油壓升高，流通閥8關閉，上腔內的油液推開伸張閥4流入下腔。由于活塞桿的存在，自上腔流來的油液不足以充滿下腔增加的容積，主使下腔產生一真空度，這時儲油缸中的油液推開補償閥7流進下腔進行補充。由于這些閥的節流作用對懸架在伸張運動時起到阻尼作用。 　　由于伸張閥彈簧的剛度和預緊力設計的大于壓縮閥，在同樣壓力作用下，伸張閥及相應的常通縫隙的通道載面積總和小于壓縮閥及相應常通縫隙通道截面積總和。這使得減振器的伸張行程產生的阻尼力大于壓縮行程的阻尼力，達到迅速減振的要求。 [編輯本段]減振器、汽車零部件的發展前景 汽車零部件作為汽車工業的基礎，是支撐汽車工業持續健康發展的必要因素。特別是當前汽車行業正在轟轟烈烈、如火如荼開展的自主開發與創新，更需要一個強大的零部件體系作支撐。整車自主品牌與技術創新需要零部件作基礎，零部件的自主創新又對整車產業的發展產生強大推動力，他們是相互影響、相互作用的，沒有整車的自主品牌，強大零部件體系的研發創新能力難以迸發，沒有強大零部件體系的支撐，自主品牌的做大作強將難以為繼。 　　2006年1-12月，中國全部汽車零部件及配件制造企業實現累計工業總產值539,704,996千元，比上年同期增長34.35%；實現累計產品銷售收入527,234,933千元，比上年同期增長34.71%；實現累計利潤總額為32,605,652千元，比上年同期增長46.79%；截止到2006年12月底，全行業規模以上企業數量為6142家。 　　2007年1-11月，中國全部汽車零部件及配件制造企業實現累計工業總產值683,525,503千元，比上年同期增長了37.34%；實現累計產品銷售收入663,529,269千元，比上年同期增長了37.45%；實現累計利潤總額48,487,363千元，比上年同期增長了68.61%；截至2007年11月底，全行業規模以上企業數量為7171家。 　　2008年1-11月，中國汽車零部件及配件制造行業實現累計工業總產值865,835,708千元，比上年同期增長了25.62%；實現累計產品銷售收入837,913,601千元，比上年同期增長了24.12%；實現累計利潤總額53,876,595千元，比上年同期增長了15.92%；截至2008年11月底，全行業規模以上企業數量為8303家。 汽車零部件生產企業脫離整車企業并形成專業化零部件集團，正成為一種全球化趨勢。國際著名的汽車及零部件企業，幾乎都在中國建立了合資或獨資企業，引進技術合資企業已超過1000家。國內一批科技含量高、效益好、規模大的汽車及零部件企業逐步成長起來。隨著國際上汽車行業開始實行零部件“全球化采購”策略及國際跨國汽車企業推行本土化策略，國內市場將出現巨大的零部件配件缺口。到2010年，中國汽車零部件國內產值將達到7000億元左右。 目前，雖然全球經濟整體下滑，但根據近四到五年的實際采購實踐，中國采購的成果并不像大量公司預測的那樣樂觀，幾乎80%以上的公司沒有達到他們采購量和采購降成本的目標。而隨著人民幣升值和出口退稅率的下降，中國采購面臨的壓力更大，國際采購商已經將目光同時轉移到越南、印度、泰國、澳大利亞等其它國家與地區。從以上看來，中國的汽車零部件產業在當前的金融危機下仍將加速增長。 7