M,彼天z探埠院本科生畢業設計（論文）外文翻譯原文標題Active regenerative chatter suppression during boring manufacturing process譯文標題鏜削再生顫振的積極抑制作者所在系別機械工程系作者所在專業xxxxx作者所在班級xxxx作者姓名xxxx作者學號xxxx指導教師姓名xxxx指導教師職稱講師完成時間2012 年 2 月北華航天工業學院教務處制譯文標題鎮削再生顫振的積極抑制原文標題Active regenerative chatter suppression during boring manufacturing process作 者Chiang C.Mei譯 名赤昂.西梅國籍 英國原文出處Robotics and Computer-Integerated Manufactering鏜削再生顫振的積極抑制 摘要鏜削的加工性能經常受加工中振動的影響。在各種振動來源中，再生顫振是最不 利的。它不僅限制了切削深度，對表面質量也有不利的影響，同時也會損害工具壽命。 盡管加工系統是一種分布式的系統，通用的控制器是根據一個簡化后的單自由度切削 過程模型來設計的。這是因為大部分切削過程只存在著一個主導模式。然而，簡化后 就會出現一些問題。首先，因為系統本身是分布式系統，理論上它是由無數個振動模 型組成，當控制器僅僅控制主要的模型，被用來控制主導模型的能量會激起原本靜止 的機構的振動，即引起所謂的溢流問題。第二、單自由度控制器設計的成功依賴于有 效的精確的模型參數（如質量當量，剛度，阻尼），但不幸的是獲取這些參數非常困 難。因為所有的參數隨加工過程的變化而變化。在這篇論文里，將從波的觀點，在廣 義的頻率中來吸取振動能來設計減振器，來提高鏜刀的加工性能，相對于當前流行的 控制器設計，波控制器的設計是真正基于分布式切削系統模型，這個抑制顫振的控制 模式的主要優點是它的穩定性。這個控制模式也可以消除控制溢流問題。一、簡介金屬切削中的振動總體上是受迫振動和自激振動引起的。受迫振動是由回轉件的 失衡引起的，比如失衡的驅動系統，伺服不穩定或者多齒零件的撞擊。受迫振動可以 認為是由振動頻率和受迫力頻率對比引起的，但相應的措施可以被用來減小或消除這 些振動來源。自激振動包括兩部分：基本類型（不可再生類型）和再生類型。不可再生式自激 振動出現在回轉件的波動表面對系統的振動沒有相影響的時候，如車螺紋。因此它只 和切削過程中受到的力有關。再生式自激振動是因為工具通過時，系統的振動和回轉 件的波動表面相互作用產生的，再生式自激振動對加工過程的影響最為不利，因此它 是這篇論文的焦點。再生顫振抑制已經被做了大量的研究，傳統設計中阻尼和剛度是被謹慎處理的。 被動和主動的減振器已將開始被應用了，我們可以根據動力學的波形圖來選擇軸的速 度和速度變化。主動控制器采用了速度反饋，最佳的和最適合的算法。盡管加工系統是分布式的， 但所有通用的主動控制器都是根據單自由度的切削模型來設計的。這樣的簡化存在一 些潛在的問題。首先，因為系統本身是分布式系統，理論上它是由無數個振動模型組 成，當控制器僅僅控制主要的模型，那被用來抑制主要模型的能量會激起原本靜止的 模型的振動，這就不可避免的引起了所謂的溢流問題。第二。單自由度控制器設計的 成功依賴于有效而精確的模型參數(如質量當量，剛度，阻尼)，但不幸的是獲取這 些參數非常困難。因為所有的參數隨金屬切削和機床移動部件的變化而變化。這篇論文的目的在于通過一種反饋波控制器來解決以上在實際分布式切削系統 中存在的問題。這種控制實際思想不僅可以消除控制溢流，也能大大的減小主要模型 和剩余的分布式模型引起的振動。此外，反饋波控制器的設計還要求有結構局部特征 方面的知識，它對系統的不確定因素敏感度很小，因此更加穩定。二、系統模型加工系統通?？梢员荒M成帶有邊界范圍的一維分布式結構。對于一個不回轉的 鏜削加工，工件比鏜刀本身還硬。典型鏜刀的扭轉硬度比彎曲硬度要大，因此它可以 被模擬成一種懸臂梁。使用一維分布式結構的彎曲歐拉梁，動力學平衡方程式如下：ei xn+p/2 心七)=f(x, t)辦 4dt 2x是沿著橫梁的距離，t為時間，f (x,t)為集中力，E為彈性模量，p為密度，A 為截面面積。古典偏微分方程的解決方案通常使用本征函數展開。響應通過無數個組件模式之 和來表達：w(x,t)=黨 4 (x)q (t)(2)i=1七(x)和qi(t) (i=1,2, 8)分別是系統的模態形狀和模態坐標。這種模態形狀 通常使之標準化：jL pA. (x)巾.(x)dx = 8 , i, j = 1,2,.8,(3)L是懸臂梁的長度，(5是狄拉克函數運動的方程式可以用模態坐標來描述：q (t) + w2q (t) = f (t),i = 1,2.,af是模態力：if (t) = jL (x,t)4 (x)dx, i = 1,2,.,a.(5)101應該指出，在實際中式組件的數量通常用n替代無窮。在一個主導模式的情況下，n =1.在切削力和刀具在切削過后留下的起伏不定的工件表面相互作用下，方程式1變?yōu)椋篸 4 w(x, t). d 2 w(x, t)EI + pA + k B(w(t) - w(t - T) = f (x, t),(6a)kc是切削剛度，由工件材料和刀具形狀決定的，B是切削深度，T是周期，p是 重疊因子，p在0到1之間變化，在最壞的情況下(p =1)，上式變?yōu)椋?4 w(x, t). - 2 w(x, t)EI + pA + k B(w(t) - w(t - T) = f (x, t),(6b)運用模態坐標來表達動力方程式，和方程1到4相同的步驟：q (t) + w2q (t) + bw2(q (t) 一 q (t - T) = f (t), i = 1,2., s.(7)ii ii i ii'b= kb / EI是關于切削深度的無量綱參數，w,是第i個模式下的自然頻率。方程式7是結構無阻尼自由振動微分方程，事實上因為沒有純粹的結構無阻尼自 由振動微分方程存在，假設結構存在粘滯阻尼，方程式就變?yōu)椋簈 (t) + 2& w q (t) + w2(q (t) + bw2(q (t) 一 q (t - T) = f (t),.(8)i' ' '' '' ',''通常&.是個0到1間很小的正數，最常用的是&0.05.三、反饋波控制的設計這種金屬切削過程中的振動抑制反饋控制是從波的觀點來設計的。當遇到一個障 礙物，入射的振動波一部分是透射，一部分是反射。主動控制力就是被用來產生這樣 一個“主動的”障礙物，以便于來控制透射和反射的振動波，考慮一個搭配的傳感器 和執行機構的安排，假設波控制力作用于一點，控制力在頻率范圍內可以寫成以下方 程式：F =-H (w)W(9)Hw (w)是控制器的頻率響應。傳輸矩陣t和反射矩陣r通過考慮力作用點的連續性和平衡性條件獲得的。t=I+p c, r=p c(10)I是單位矩陣i iH (w)/ 、c =, h =,(11)1 1w 3/2 -(1 + i) H (w)'H (w) = H (w) / 4<'(pA) 3 EI .w一系列可能的控制方法在反饋波控制器的設計過程中被研究。這里提供一個最佳的能量吸收控制器，被設計來最大化的吸收在一個寬頻帶里由起伏的部件引起的振動 能。也就是讓|,|2 +陣最小。因此最佳的控制器被認為是：H(w) = a4(pA)3 EI (1 + i)w3/2.(12)注意理想的控制器具有頻率依賴性，在實際執行中，控制器必須接近于理想。在 通常金屬切削過程中，只存在一個主模式。因此這個控制器可以通過調節控制器在主 模式的頻率內達到最佳來獲得。這接近于最佳的控制器是：H (w) = c + c (iw),(13)其中 c = 24(pA)3Eiwd3/2 and c2 = 2&pA)3EIwj假設波控制力被應用于七點，控制力相對于變量t的方程式可寫為：f (x, t) = -c w(x, t) + c w(x, t)6 (x - x ).(14)它可以看成比例和導數調節器?？刂圃鲆娴脑O(shè)計也是從從波的觀點出發的。實現了波控制后方程式(6b)變成：d4 w(x, t). d2 w( x, t)EI + pA 初2+ k B(w(t) - w(t - T) = f (x, t) + f (x, t),dx 4(15)運動方程式可以再一次分解:寫成矩陣形式:q (t) + 2& w q (t) + w2 q (t) + bw2 (q (t) - q (t - T) +1 i i ii ii iic 工巾(x 沖(x )q (t) + c 工巾(x 沖(x )q (t) = f (t)2 i c i c ii j c i c jij=1j=1(16)M q(t) + C q(t) + Kq(t) + Kq(t - T) = f (t),q = q (t)q (t)：q (t) t , f = f (t) f (t).f (t)t ,12n12nC = A + c © (x 沖(x ), K = (1 + b)A + c © (x 沖(x ),ij ij 2 ij c j c ijij 1 i c jKd =-bA.ij 2 ij c j c ij其中M=I,矩陣上T表示向量的裝置。引入狀態向量X(t)=T.qT : q(17),方程式17(18)可寫為:X (t) = AX (t) + At X (t - T) + Bf (t)與系數矩陣0-M -1K1-M -1C,00 ,At = - M -1K0and,BLd 0M -1四、穩定性高的金屬切削率和高的表面質量無疑是加工中最重要的問題。然而合適的切削率 建立在機床系統的動力學基礎上，已知的加工系統存在一個不穩定的臨界值，波形圖 是用來描述臨界值和允許的最大切削深度的，刀具的性能和刀具/工件的旋轉速度之 間的關系。在加工系統的研究中波形圖是一個非常有用的工具。由方程式18,得特征方程式：sI - A - A e一st = 0.(19)T波形圖是通過設置方程式19里的S-來解特征方程，導致最大的允許切削深度和 無窮小參數B有關，在給定切削速度的情況下。根據以上研究，在切削過程中只存在一個主要的模式(解釋了為什么主動控制器 的設計是基于一個自由度的離散型模型)。因此，在以下數字實例中，我們假定只有 一個主要模型，即N=1。圖1是沒有控制的情況下工件系統的波形圖，圖2是力作用于0.5L的情況下工 件系統的波形圖。鏜刀被認為是彈性模量E = 180GN/m2，密度p = 8600mg/m3.的鋼 桿。桿的直徑為2英寸，長徑比為10.結構的阻尼系數為0.01.在系統的主要模式下 控制器將是最佳的。固有頻率七假定為791.5rad/s.因此 匕=2 x 791.53/2,七=2 x 791.51/2，從圖1和圖2可以看出切削深度在有控制后得到顯著 地提高。0.20.060.040.020：OCO 20DO 3000主軸就400050006000圖1.未控制時的系統穩定性0.2° 010002000300040005000 60DQ主軸錘.圖2.控制后景統的穩定性需要指出的是金屬切削過程中的動力是唯一的，系統的參數在切削過程中不斷的 變化，盡管單自由度模式聽起來和在一個主要模式情況下的分散式系統非常接近，但 它卻需要連續的模式參數才能適當?shù)墓ぷ?。不幸的是以前的研究沒有一份提到這個問 題。反饋波控制器是基于機構本身性能在一個寬頻范圍內來最佳的吸收振動能的原理 來設計的，控制器時穩定的隨著系統參數的改變。時間的時域響應通過q (頃=1,2,.)來獲得，然后把他們帶到方程式2中。采用庫 i塔法和拉格朗日插值定理解決微分問題，方程變?yōu)槿缦拢? (x) = cosh k x cos k x b (sinh k x sin k x),(20)iii iii固有頻率和波數的關系式如下w = k2；EA.i i以為只有一個主模式，響應可以近似描述為：w(x, t) =8 (x)q (t),(21)時間圖4,系曲制后的時間響應I4 1（x）由方程式20給出，七=1.875/L （L為棒料的長度），。1= 0.7341。比如，從圖1可以看出在4400rpm時，無量綱的切削深度b為0.01，當增加b到 0.04時根據波形圖會發生不穩定的振動，圖3中的時間響應已經證實了。這個響應發 生在刀具的工件的接觸點上，假定是懸臂梁的頂部。在安裝主動控制器后，在4400rpm無量綱的切削深度b為0.04時的不穩定切削 得到了控制。圖4的時間響應證實了這一發現。響應圖說明了反饋波控制很打的提高 了允許的切削深度，在軸的速度給定情況下。隨著切削深度增加，生產力也得到了提 高。五、結論在這篇論文里，一個從波的觀點出發在一定頻率范圍內吸收振動能的減振器被應 用在再生振動的鏜削過程中。盡管在系統中有一個主要的模式主導響應，但剩下的模 式也或多或少影響著系統的振動。此外，當控制器僅僅由主模式來設計時，就可能會 出現控制溢流（被用來控制主要模式的力會引起剩余模式的變化），就像從勃朗寧實 驗觀察的一樣。在這次研究中，控制器在在很寬的頻率內設計的，阻尼在這頻率范圍 內的模式上。因此它不僅能消除溢流問題，也能很好地減小主模式和其他模式引起的 振動。原文：active regenerative chatter suppression during boring manufacturingprocessAbstractMachining performance such as that of the boring process is often limited by chatter vibration at the tool-workpiece interface. Among various sources of chatter, regenerative chatter in cutting systems is found to be the most detrimental. It limits cutting depth (as a result, productivity), adversely affects surface finish and causes premature tool failure. Though the machining system is a distributed system, all current active controllers have been designed based upon a simplified lumped single degree of freedom cutting process model. This is because it was found that in the majority of cutting processes, there exists only one dominating mode. However, such simplification does have some potential problems. First, since the system itself is a distributed system, theoretically it consists of infinite number of vibration modes. When the controller is designed to control the dominating mode(s)1. IntroductionChatter in metal cutting process, in general, is the result of both forced and self-excited vibrations.Forced vibration is due to the unbalance of rotating members, such as unbalanced driving system, a servo instability, or impacts from a multi-tooth cutter. In practice, the forced vibration sources can be traced by comparing the frequency of chatter with the frequency of the possible force functions. Corresponding measures can then be taken to reduce/eliminate such vibration sources.Self-excited vibration consists of two types, namely primary (or non-regenerative type) and regenerative type. The primary/non-regenerative type of self-excited vibration occurs when theses is no interaction between the vibratory motion of the system and the adulatory surface produced in the revolution of the work piece, such as that in threading. Hence if is inherently related to the dynamics of the cutting process. While the regenerative type of self-excited vibration is due to the interaction of the cutting force and the work piece surface undulations produced by previous tool passes. The regenerative type of self-excited vibration is found to be the most detrimental phenomena in most machining process, hence it becomes the focus of this paper.A considerable amount of work has been done on regenerative chatter suppression. Conventional structural damping and stiffness treatments are considered. Both passive and active vibration absorbers are implemented. Based on the dynamics of stability lobe pockets, spindle speed variation and spindle speed selection strategies are proposed.Active controllers are also designed using rate feedback, optimal and adaptive algorithms. Though the machining system is a distributed system, all current active controllers were designed based upon a simplified lumped single degree of freedom cutting process model. This is because it was found that in the majority of cutting process, there exists only one dominating mode. However, such simplification does have some potential problems. First, since the system itself is a distributed system, theoretically it consists of infinite number of vibration modes. When the control is designed to control only the dominating mode(s), the energy designed to suppress the particular mode(s) may excite the rest of the structural modes, This can causes a spillover problem. Second, the success of the designed controller of a simplified single degree of freedom system relies on the availability of accurate model parameters (such as the effective mass, stiffness and damping), which is unfortunately very hard to acquire. This is not only because theCutting process itself is a dynamic process but because the cutting process itself is a dynamic process but also because the system involves movable components of the machine tool and the work piece .This paper aims at solving the above mentioned problems by implementing a feedback wave controller on the real distributed cutting system model. Such a control design strategy not only eliminates control spillover, but also greatly reduces chatter caused by the dominating mode as well as that by the rest of the design of the feedback wave control requires only knowledge with regard to the local properties of the structure. It is thus much less sensitive to global systems uncertainties, as a result, more robust.2. System modelMachining systems, in general, can be modeled as one-dimensional distributed structures with various boundary conditions. For a non-rotating boring process, the work piece is much stiffer than the boring bar itself. And typically boring bars are much stiffer in torsion than in bending. Hence it can be modeled as a cantilevered rod in bending. Using Euler-Bernoulli s bending model for one-dimensional uniform distributed structure, the equation of motion is as follows:84w(x, t)a 2w(x, t)EI + P A= f (x, t),(1)8x4at 2where x is the distance along the beam, t the time, f(x,t) the external force, E the Young s modulus, I the cross-sectional area moment of inertia, p the mass density and A the area of cross section of the boring bar.The solution to the classical partial differential equation is usually found using Eigen function expansions. The response can be expressed as a sum of an infinite number of modal components asw(x, t) = u n. (x)q (t)(2)i=1Where n (x) and q (t) (i=1,2, 8)are the mode shapes and modal coordinates of the system , respectively. The mode shapes are in general, mass-normalized such thatjL pAn. (x)n. (x)dx = 8 i, j = 1,2,.8,(3)where L is the length of the structure and。the Dirac delta function.The equations of motion can be written in terms of the model coordinates as.q (t) + w2q (t) = f (t), i = 1,2., 8.(4)i.where f is the i th modal force given byif (t) = jL (x, t)n (x)dx, i = 1,2,., 8.(5)i01It should be pointed out that in practice. Only a finite number of modes are excited, as a result, the number of modal components is in general n instead of 8 .In the case of one dominating mode, n=1.Now considering the dynamic interaction of the cutting force and the workpiece surface undulations produced by previous tool passes during the cutting process, Eq.(1) then becomes 1d4 w(x, t). d2 w(x, t)EI + pA + k B(w(t) - pw(t - T) = f (x, t),(6a)Where k is cutting stiffness determined by workpiece material and tool geometry, B the depth of cut and T the tooth passing period, p is the so-called overlap factor, which accounts for the overlapping of successive cuts. The value of varies between 0 and 1. Considering the worst-case scenario (wherep =1), then the above equation becomes-4 w(x, t). - 2 w(x, t)EI + pA + k B(w(t) - w(t - T) = f (x, t),(6b)The corresponding equations of motion in terms of the modal coordinates, by following the same procedures as that of Eqs.(1)-(4),are.q (t) + w2q (t) + bw2(q (t) 一 q (t - T) = f (t), i = 1,2., 8.(7)i' i/Where b= k b / EI is the cutting depth-related dimensionless parameter and w the natural frequency of the I i th mode.Eq.(7) describes an undammed structure. Since no purely undammed structures exist inreality, assuming viscous damping in the structure, the equation of motion is then rewritten as(8)q(t)+2&w q(t) + w2 (q(t)+ bw2 (q(t) 一 q(t - T)= f (t),.i ii iiiiUsually & is a small positive number between 0 and 1, with most common values of3. Feedback wave control designThe vibration suppression feedback control of the metal cutting process is designed from wave standpoint. Upon meeting a discontinuity an incident vibration wave is partially transmitted and partially reflected. An active control force is applied to create such an active discontinuity; so as to control the transmitted and/or reflected vibration waves. Considering a collocated sensor and actuator arrangement and assuming the wave control force being a point force, the control force can be written in frequency domain asF =-H (w)W ,(9)Where H (w) is frequency response of the controller.The transmission and reflection matrices t and r are obtained considering the continuity and equilibrium conditions at the force applied pointt=I+p c, r印 c,(10)Where I is the identity matrix and(11)H (w)w 3/2 -(1 + i) H (w)Where H (w) = H (w)/4 (p4)3 EI .wA number of possible control strategies have been studied in feedback wave control design. Here an optimal energy absorbing controller is adopted, in which the controller is designed to maximize the absorbed vibration energy caused by the propagating wave components in a broad frequency band, in other words to minimize r2 + |t|2. In the case the optimal controller is found to beH(w) = a<'(p4)3 EI (1 + i)w3/2.(12)Note that the ideal controller is frequency dependent and non-causal. For a practical implementation, a causal controller must be found which an approximation to the ideal 29 is. It is found generally that in metal cutting processes there exists only one be obtained by turning the controller to be optimal at the corresponding natural frequency of the dominating mode w , the approximated optimal controller is thenH (w) = c + c (iw),(13)Where 匕=2不pA)3Eiw3/2 and c2 = 2&pA)3EIwjAssuming the point wave control force is applied at xc, the control force in time domain is given byf (x, t) = -c w(x, t) + c W(x, t)6 (x - x ).(14)It can be seen that it corresponds to proportional and derivative controller. Here the control gains are designed, however, from wave standpoint.After the implementation of wave control, Eq.(6b) becomesd4 w(x, t). d2 w(x, t)EI8 4+ pA初2+ k B(w(t) - w(t - T) = f (x, t) + f (x, t),(15)The equation of motion can again be decomposed in terms of the uncontrolled modes and becomesq (t) + 2& w q (t) + w2 q (t) + bw2(q (t) - q (t - T) +i i i i i i i i iVv(16)c 乙巾(x )4 (x )q (t) + c 乙巾(x )4 (x )q (t) = f (t)2 i c i c ii j c i c jij=1j=1Which can be written in matrix form asM q(t) + C q(t) + Kq (t) + K q (t - T) = f (t),(17)Whereq = q (t)q (t).q (t) t , f = f (t) f (t).f (t)t ,12n12nC = A + c 4 (x )4 (x ), K = (1 + b)A + c 4 (x )4 (x ),ij ij 2 ij c j c ijij 1 i c j c% =-bA.In which M=I, the identity matrixA = diag(w2 )andi, j = 1,2,.,n. iSuperscript T denotes the transpose of vector.TIntroducing state vector X(t) = qT : q , Eq.17can be rewritten in state-space fromasX(t) = AX (t) + A.X (t - T) + Bf (t)(18)With the coefficient matrices1-M -iC-M -i Kd0M -i4. StabilityHigh metal removal rate with quality surface finish is undoubtedly the most important issue in machining. While the applicable metal removal rate depends on the dynamics of the machine tool system, an instability threshold exists for a given machining system. Stability charts (or lobes) describe the relationship among the stability threshold, the relationship among the stability threshold, the maximum allowable cutting depth, the tool dynamics and the rotational speed of the tool/workpiece. The stability lobe diagram has been an important tool in the study of chatter in machining systems.From Eq.(18), the characteristic equation is obtained as(19)sI - A - Ae-st = 0.The stability lobe is obtained by setting s in Eq.(19) to jw and solving the characteristic equation, which result in the maximum allowable cutting depth related dimensionless parameter b at a given tooth passing speed .According to previous studies, there, in general, exists only one dominating mode in most metal cutting process (which explains the reason that almost all the active control design was based on a single degree of freedom discrete model). Hence in the numerical example considered below, it is assumed that the number of dominating mode is one , that is , n=1.Fig.1 shows the stability lobe of the uncontrolled tool system and Fig.2 shows the stability lobe of the controlled tool system with the control force applied at 0.5L. The boring bar is assumed to be a steel bar with Youngs modulus E = 180GN / m 2and mass density p = 8600mg / m3. The diameter of the rod is 2 inches with slenderness ratio being 10. The damping ratio of the structure is assumed to be 0.01. The controller is tuned to be optimal at the system s dominating mode, that is the first natural frequency w ,which is calculated as 791.5rad/s. Accordingly, one has c = 2 x 791.53/2 and, c = 2 x 791.51/2 .From Figs.1 and 2 it can be seen that the cutting depth is improved greatly after control.It should be point out that the dynamics of metal cutting process is unique in the way that the systems parameters change dynamically during metal removal process. Though the previous lumped single degree of free model is theoretically sound in approximating the distributed system in the case of one dominating mode, it demands continuous model parameters identification and updating to work appropriately. Unfortunately, none of the previous studies addressed this issue. With the feedback wave controller designed based on the local properties of the structure to optimally absorb vibration energy in a broad frequency band, the controller is robust to changes in systems parameters.The time domain response is obtained by finding the model states q (t)(i = 1,2,.) numerically and then substituting them into Eq.(2). The adaptive Runge-Kutta-Ferlberg method 31 is used to solve the differential equations numerically with the delay term calculated using the Lagrange interpolation theorem.The mode shapes of a cantilever are given as8 (x) = cosh k x cos k x b (sinh k x sin k x),(20)iii iiiWhere k L = , b =，訕匕乙，詛匕，an, j -1,2, A, 8 The natural frequencies i 2 icos k L + cos k Land the wave numbers are related by w = k2 X;EI / pA.In the case that only one mode is dominating, the res