附錄 附錄 1 is in on on to of . s s s To in to to on “ It is to so on is in On s to to s to to on is in or in is to is to in to be s on s to It s in of to s to be in to is s ). of is of K. to is K is K is s of K, to of t BS by a so on of is BS is s 2. BS BS is 4 to a in At is To BS on ID so of by he 0 of e=ID be BS s up to BS of p, Ki d, s to 0 by by to be to s is s in of k, in by s s in S,×S) to to ). , by to to e=is as s as as s of C, is an U = × E + (1C is to of is is to s is in to is is to be to on 1, 2 (0,1), 1 in to to s s of as BS , of so on of or a to BS of at to s is s s by a is of is a on 5% 0% s by to to in by it is a so on is of of BS to be a is is t s as s by a is mm In to to in s a a in to to be to of is as 1) to to go is to 2) s in s to at 3) s to to to to or CU is on on by is , , , . 101tz is is to of is is is of BS in It is a on s 5 00 s on a s to go in to s or or of to to 3. by BS 1) or in s in to s (2) is BS a is (3) BS to 4. of a of to of s s is is BS it by no of of is BS s is to on to is to BS in (1) at BS to be at is to a in of to s to be in is on in s to to a as a of so on s to (2) Is is s in BS to is is s so to in BS on on by it is s is so on be (3) by BS 10, of in to in be in so on to s in to so on In to CU by Or to s is a to to CU CU 11, to 5. he in of or of At BS on of by In by to 汽車防抱死制動系統（ 摘要 ： 本文簡要介紹了汽車防抱死制動系統（ 稱 控制原理，對目前汽車防抱死制動系統所采用的控制技術進行了綜述，并對其發展趨勢進行了預測。 關鍵詞 ： 汽車 ； 防抱死制動系統 ； 控制技術 隨著汽車工業的迅猛發展和高速公路的不斷修建，汽車的行駛安全性越來越為人們 重視 。 為了 全面滿足制動過程中汽車對制動的要求，使制動器制動力分配更趨合理。汽車防抱死制動系統（簡稱 越來越多地應用在汽車上。 “中文譯為 “ 防鎖死剎車系統 ”. 它是一種具有防滑、防鎖死等優點的汽車安全控制系統。 分機械式和電子式兩種。 現代汽車上大量安裝防抱死制動系統， 有普通制動系統的制動功能，又能防止車輪鎖死，使汽車在制動狀態下仍能轉向，保證汽 車的制動方向穩定性，防止產生側滑和跑偏，是目前汽車上最先進、制動效果最佳的制動裝置。 普通制動系統在濕滑路面上制動，或在緊急制動的時候，車輪容易因制動力超過輪胎與地面的摩擦力而安全抱死。 汽車防抱死制動系統是指汽車在制動過程中能實時判定車輪的滑動率，自動調節作用在車輪上的制動力矩，防止車輪抱死。從而獲得最佳制動效能的電子裝置。它能把車輪的滑動率控制在一定的范圍之內，充分地利用輪胎與路面之間的附著力，有效地縮短制動距離，顯著地提高車輛制動時的可操縱性和 穩定 性，從而避免了車輪抱死時易出現的各種 交通事故。 隨著制動強度的增加，車輪滾動成分越來越少，而滑動成分越來越多，一般用滑動率S 來說明制動過程中滑動成分的多少。滑動率越大，滑動成分越少。 其中： u 車輪 中心 的速度； r 沒有地面制動力時的車輪滾動半徑； w 車輪的角速度。 縱向和側向附著系數可表達為車輪滑動率的函數（如圖 1）。最大縱向附著系數所對應的滑動率稱為臨界穩定點 據控制理論把滑動率小于 區域稱為穩定制動區， 后的為非穩定制動區。 是利用道路與輪胎之間的關系，強制性地把車輪滑動率控制 在臨界穩定點 近，使路面附著性能得到最充分的發揮，從而達到最佳的制動效果。 圖 1 附著系數 目前所采用的 要由輪速傳感器，電子控制單元，壓力控制閥和線束、管路等附件組成。 開發主要是研究設計優化運算和控制程序軟件，實現實時精確制動調節的技術，同時提高硬件的水 平。 采用的控制技術 控制效果很大