單級圓柱齒輪減速器設計,單級圓柱齒輪減速器設計,圓柱齒輪,減速器,設計 目 錄 設計計劃任務書 ﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎1 傳動方案說明﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎2 電動機的選擇﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎3 傳動裝置的運動和動力參數﹎﹎﹎﹎﹎﹎﹎﹎5 傳動件的設計計算﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎6 軸的設計計算﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎8 聯軸器的選擇﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎10 滾動軸承的選擇及計算﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎13 鍵聯接的選擇及校核計算﹎﹎﹎﹎﹎﹎﹎﹎﹎14 減速器附件的選擇﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎15 潤滑與密封﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎16 設計小結﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎16 參考資料﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎﹎16 1 1.擬定傳動方案 　為了估計傳動裝置的總傳動比范圍，以便選擇合適的傳動機構和傳動方案，可先由已知條件計算其驅動卷筒的轉速nw,即 v=1.1m/s;D=350mm; nw=60*1000*v/(∏*D)=60*1000*1.1/(3.14*350) 一般常選用同步轉速為１０００r/min或１５００r/min的電動機作為原動機，因此傳動裝置總傳動比約為１7或25。 2.選擇電動機 １）電動機類型和結構形式 按工作要求和工作條件，選用一般用途的Ｙ（ＩＰ４４）系列三相異步電動機。它為臥式封閉結構。 ２）電動機容量 （１）卷筒軸的輸出功率Ｐｗ F=2800r/min; Pw=F*v/1000=2800*1.1/1000 (2)電動機輸出功率Pd Pd=Pw/t 傳動裝置的總效率　　t=t1*t2^2*t3*t4*t5 式中，t1,t2,…為從電動機到卷筒之間的各傳動機構和軸承的效率。由表２－４查得： 彈性聯軸器 1個 t4=0.99; 滾動軸承 2對 t2=0.99; 圓柱齒輪閉式 1對 t3=0.97; V帶開式傳動 1幅 t1=0.95; 卷筒軸滑動軸承潤滑良好 1對 t5=0.98; 則 t=t1*t2^2*t3*t4*t5=0.95*0.99^2*0.97*0.99*0.98＝0.8762 故 Pd=Pw/t=3.08/0.8762 （３）電動機額定功率Ped 由第二十章表２０－１選取電動機額定功率ped=4KW。 3）電動機的轉速 為了便于選擇電動事，先推算電動機轉速的可選范圍。由表２－１查得V帶傳動常用傳動比范圍2~4，單級圓柱齒輪傳動比范圍3~6， 可選電動機的最小轉速 Nmin=nw*6=60.0241*6=360.1449r/min 可選電動機的最大轉速 Nmin=nw*24=60.0241*24=1440.6 r/min 同步轉速為960r/min 選定電動機型號為Ｙ１32Ｍ1－６。 ４）電動機的技術數據和外形、安裝尺寸 由表２０－１、表２０－２查出Ｙ１32Ｍ1－６型電動機的方根技術數據和 外形、安裝尺寸，并列表刻錄備用。 電機型號 額定功率 同步轉速 滿載轉速 電機質量 軸徑mm Y132M1-6 4Kw 1000 960 73 28 大齒輪數比小齒輪數=101/19=5.3158 ３．計算傳動裝置總傳動比和分配各級傳動比 １）傳動裝置總傳動比 nm=960r/min; i=nm/nw=960/60.0241=15.9936 ２）分配各級傳動比 取V帶傳動比為 i1=3; 則單級圓柱齒輪減速器比為 i2=i/i1=15.9936/3=5.3312 所得i2值符合一般圓柱齒輪和單級圓柱齒輪減速器傳動比的常用范圍。 ４．計算傳動裝置的運動和動力參數 １）各軸轉速 電動機軸為０軸，減速器高速軸為Ⅰ軸，低速軸為Ⅱ軸，各軸轉速為 n0=nm; n1=n0/i1=60.0241/3=320r/min n2=n1/i2=320/5.3312=60.0241r/min ２）各軸輸入功率 按機器的輸出功率Pd計算各軸輸入功率，即 P0=Ped=4kw 軸I 的功率 P1=P0*t1=4*0.95=3.8kw 軸II功率 P2=P1*t2*t3=3.8*0.99*0.97=3.6491kw ３）各軸轉矩 T0=9550*P0/n0=9550*4/960=39.7917 Nm T1=9550*P1/n1=9550*3.8/320=113.4063 Nm T2=9550*P2/n2=9550*3.6491/60.0241=580.5878 Nm 二、設計帶輪 1、計算功率 P=Ped=4Kw 一班制，工作８小時，載荷平穩，原動機為籠型交流電動機 查課本表８－１０，得KA=1.1; 計算功率 Pc=KA*P=1.1*4＝4.4kw 2選擇普通Ｖ帶型號 n0 =960r/min 根據Pc=4.4Kw，n0=960r/min,由圖13-15（205頁）查得坐標點位于A型 d1=80~100 ３、確定帶輪基準直徑 表８－１１及推薦標準值 小輪直徑 d1=100mm; 大輪直徑 d2=d1*3.5=100*3.5=350mm 取標準件 d2=355mm; 4、驗算帶速 驗算帶速 v=∏*d1*n0/60000=3.14*100*960/60000=5.0265m/s 在5~25m/s范圍內 從動輪轉速 n22=n0*d1/d2=960*100/355=270.4225m/s n21=n0/3.5=960/3.5=274.2857m/s 從動輪轉速誤差=(n22-n21)/n21=270.4225-274.2857/274.2857 =-0.0141 5、V帶基準長度和中心距 初定中心距 中心距的范圍 amin=0.75*(d1+d2)=0.75*(100+355)=341.2500mm amax=0.8*(d1+d2)=0.8*(100+355)=364mm a0=350mm; 初算帶長 Lc=2*a0+pi*(d1+d2)/2+(d2-d1)^2/4/a0 Lc = 1461.2mm 選定基準長度 表8-7,表8-8查得 Ld=1600mm; 定中心距 a0+(Ld-Lc)/2=(1600-1461.3)/2=419.4206mm a=420mm; amin=a-0.015*Ld=420-0.015*1600=396mm amax=a+0.03*Ld=420+0.03*1600=468mm 6、驗算小帶輪包角 驗算包角 ＝180-(d2-d1)*57.3/a=180-(355-100)*57.3/a 145.2107 >120度 故合格 7、求V帶根數Z 由式（13-15）得 查得 n1=960r/min , d1=120mm 查表13-3 P0=0.95 由式13-9得傳動比 i=d2/(d1(1+0.0141)=350/(100*(1+0.0141)=3.5 查表（13-4）得 由包角145.21度 查表13-5得Ka=0.92 KL=0.99 z=4.4/((0.95+0.05)*0.92*0.99)=3 8、作用在帶上的壓力F 查表13-1得q=0.10 故由13-17得單根V帶初拉力 三、軸 初做軸直徑： 軸I和軸II選用45#鋼 c=110 d1=110*（3.8/320）^(1/3)=25.096mm 取d1=28mm d2=110*(3.65/60)^（1/3）=43.262mm 由于d2與聯軸器聯接，且聯軸器為標準件，由軸II扭矩，查162頁表 取YL10YLd10聯軸器 Tn=630>580.5878Nm 軸II直徑與聯軸器內孔一致 取d2=45mm 四、齒輪 1、齒輪強度 由n2=320r/min,P=3.8Kw,i=3 采用軟齒面，小齒輪40MnB調質，齒面硬度為260HBS，大齒輪用ZG35SiMn調質齒面硬度為225HBS。 因， SH1=1.1， SH2=1.1 ， ， 因：，，SF=1.3 所以 2、按齒面接觸強度設計 設齒輪按9級精度制造。取載荷系數K=1.5，齒寬系數 小齒輪上的轉矩 按 計算中心距 u=i=5.333 mm 齒數z1=19,則z2=z1*5.333=101 模數m=2a/(z1+z2)=2.0667 取模數m＝2.5 確定中心矩a=m(z1+z1)/2=150mm 齒寬b= b1=70mm,b2=60mm 3、驗算彎曲強度 齒形系數YF1=2.57，YF2=2.18 按式（11-8）輪齒彎曲強度 4、齒輪圓周速度 按162頁表11-2應選9做精度。與初選一致。 五、軸校核： 圓周力Ft=2T/d1 徑向力Fr=Ft*tan =20度 標準壓力角 d=mz=2.5*101=252.5mm Ft=2T/d1=2*104.79/252.5=5852.5N Fr=5852.5*tan20=2031.9N 1、求垂直面的支承壓力Fr1,Fr2 由Fr2*L-Fr*L/2=0 得Fr2=Fr/2=1015.9N 2、求水平平面的支承力 FH1=FH2=Ft/2=2791.2N 3、畫垂直面彎矩圖 L=40/2+40/2+90＋10=140mm Mav＝Fr2*L/2＝1015.9*140/2=71.113Nm 4、畫水平面彎矩圖 MaH=FH*L/2=2791.2*140/2=195.384Nm 5、求合成彎矩圖 6、求軸傳遞轉矩 T=Ft*d2/2=2791.2*2.5*101/2=352.389Nm 7、求危險截面的當量彎矩 從圖可見a-a截面是最危險截面，其當量彎矩為 軸的扭切應力是脈動循環應力 取折合系數a=0.6代入上式可得 8、計算危險截面處軸的直徑 軸的材料，用45#鋼，調質處理，由表14-1查得 由表13-3查得許用彎曲應力， 所以 考慮到鍵槽對軸的削弱，將軸的最小危險直徑d加4%。 故d=1.04*25.4=26.42mm 由實際最小直徑d=40mm,大于危險直徑 所以此軸選d=40mm,安全 六、軸承的選擇 由于無軸向載荷，所以應選深溝球軸承6000系列 徑向載荷Fr=2031.9N，兩個軸承支撐，F(xiàn)r1=2031.9/2＝1015.9N 工作時間Lh＝3*365*8=8760（小時） 因為大修期三年，可更換一次軸承 所以取三年 由公式 式中 fp=1.1,P=Fr1=1015.9N,ft=1 (工作環境溫度不高) （深溝球軸承系列） 由附表選6207型軸承 七、鍵的選擇 選普通平鍵A型 由表10-9按最小直徑計算，最薄的齒輪計算 b=14mm,h=9mm,L=80mm,d=40mm 由公式 所以 選變通平鍵，鑄鐵鍵 所以齒輪與軸的聯接中可采用此平鍵。 八、減速器附件的選擇 1、通氣器： 由于在外界使用，有粉塵，選用通氣室采用M181.5 2、油面指示器： 選用油標尺，規格M16 3、起吊裝置：采用箱蓋吊耳，箱座吊耳 4、放油螺塞：選用外六角細牙螺塞及墊片M161.5 5、窺視孔及視孔蓋 選用板結構的視孔蓋 九、潤滑與密封： 1、齒輪的潤滑：采用浸油潤滑，由于低速級大齒輪的速度為： 查《課程設計》P19表3-3大齒輪浸油深度為六分之一大齒輪半徑，所以取浸油深度為30mm。 2、滾動軸承的潤滑 采用飛濺潤滑在箱座凸緣面上開設導油溝，并設擋油盤，以防止軸承旁齒輪嚙合時，所擠出的熱油濺入軸承內部，增加軸承的阻力。 3、潤滑油的選擇 齒輪與軸承用同種潤滑油較為便利，考慮到該裝置用于小型設備選用 L-AN15潤滑油 4、密封方式選取： 選用凸緣式端蓋，易于調整軸承間隙，采用端蓋安裝氈圈油封實現密封。 軸承蓋結構尺寸按用其定位的軸承外徑?jīng)Q定。 設計小結： 二、課程設計總結 設計中運用了Matlab科學工程計算軟件，用notebook命令調用MS—Word來完成設計說明書及設計總結，在設計過程中用了機械設計手冊2.0 軟件版輔助進行設計，翻閱了學過的各種關于力學，制圖，公差方面的書籍，綜合運用了這些知識，感覺提高許多，當然尤其是在計算機軟件CAD 方面的運用，深切感到計算機輔助設計給設計人員帶來的方便，各種設計，計算，制圖全套完成。 由于沒有經驗，第一次做整個設計工作，在設計過程中出現了一些錯誤比如線形，制圖規格，零件設計中的微小計算錯誤等都沒有更正，設計說明書的排版也比較混亂等等。對圖層，線形不熟悉甚至就不確定自己畫出的線，在出圖到圖紙上時實際上是什么樣子都不知道 ，對于各種線寬度，沒有實際的概念。再比如標注較混亂，還是因為第一次做整個設計工作，沒有經驗，不熟悉。 這次設計的目的是掌握機械設計規律，綜合運用學過的知識，通過設計計算，繪圖以及運用技術標準，規范設計手冊等有關設計資料進行全面的機械設計技能訓練。目的已經達到，有許多要求、標準心中雖然明確理解掌握但是要全力，全面的應用在實際中，還有待于提高水平。 雖然它可能不是良好、優秀，但是既然教學環節、課程設計目的已經達到，那么這次設計做的就是完全合格的。當然還受軟件的熟悉，運用程度的影響，所有這些必須得參加實踐，接觸實際工程設計中才能提高。帶輪，齒輪，軸，軸承這些關鍵的設計計算都達到合格，并且用機械設計手冊2.0 軟件版的驗證了。 通過這次課程設計，感到機械設計綜合了力學，公差，材料，制圖等學科的知識，要好了這些功課，才能做好機械設計。 參考資料： 《工程力學》，《機械設計基礎》，《機械設計指導》，《互換性技術與測量》，《機械制圖》 Nw=60.0241r/min Pw=3.08Kw 效率t=0.8762 Pd = 3.5150 Ped=4Kw i=15.9936 i1=3 i2=5.3312 n0=960r/min n1=320r/min n2=60.0241r/min P0=4Kw P1=3.8Kw P2=3.6491Kw T0=39.7917Nm T1=113.4063Nm T2=589.5878Nm KA=1.1 Pc=4.4Kw d1=100mm d2=355mm 初定中心距 a0=350mm Lc=1461.3mm Ld=1600mm 中心距 a=420mm z=3根 預緊力 FQ＝274.3N d1=28mm d2=45mm YL10YLd10 T1=113.4063Nm m=2.5 a=150mm =20度 Ft=5582.5N Fr=2031.9N FH1=FH2=2791.2N Mav=71.113Nm MaH=195.38Nm Ma＝216.16Nm Me=457.15Nm Fr1=1015.9N Lh=8760小時 6207型 bhL=14980 19 編號 無錫太湖學院 畢業設計（論文） 相關資料 題目：單級減速機箱體和箱蓋工藝工裝設計 機電 系 機械工程及自動化專業 學 號： 　　　 0923199　　　　 學生姓名： 張亞東 指導教師： 　 鮑虹蘇（職稱：高工 ） （職稱： ） 2013年5月25日 目 錄 一、畢業設計（論文）開題報告 二、畢業設計（論文）外文資料翻譯及原文 三、學生“畢業論文（論文）計劃、進度、檢查及落實表” 四、實習鑒定表 無錫太湖學院 畢業設計（論文） 開題報告 題目：單級減速機箱體和箱蓋工藝工裝設計 信機 系 機械工程及自動化專業 學 號： 0923199 學生姓名： 張亞東 指導教師： 鮑虹蘇 （ 職稱：高工） （職稱： ） 2012年11月24日 課題來源 機械制造業是一個國家最基礎的行業，也決定了一個國家制造業的整體水平現在中國已經是一個制造大國，中國的制造業規模已經達到世界第四位，僅次于美國、日本和德國。 研究內容 本設計是針對減速機箱體工藝的制作，主要研究的是減速機箱蓋的工藝過程、減速機的底座的工藝過程、減速機箱體合裝后的工藝過程以及對該技術的測試和其實用性的研究。并由此做出了對現行的減速機的箱體的改造和進一步的完善。在這次的箱體工藝制造中，對一些主要程序比如說結合面聯接孔、鉆頂面螺紋底孔、攻螺紋、鉆側面測油孔、放油孔、螺紋底孔、沉孔、攻螺紋 等的研究。 擬采取的研究方法、技術路線、實驗方案及可行性分析 設計任務 1） 設計一個中等復雜的零件的加工工藝規程； 2） 設計一個專用夾具； 3） 編寫設計說明書。 根據設計任務做出減速機箱的基本設計任務 1）繪制零件工件圖一張； 2）繪制毛坯—零件合圖一張； 3）編制機械加工工藝規程卡片一套； 4）編寫設計說明書一份； 5）收集和研究原始資料，為夾具結構設計做好技術準備。 6）初步擬定夾具結構方案，繪制夾具結構草圖，進行必要的理論計算和分析。 選擇最佳的夾具結構方案，確定夾具精度和夾具總圖尺寸、公差配合與技術要求。 7） 繪制夾具總圖和主要非標準件零件圖，編寫設計說明書。 8）編制夾具特殊使用維護、操作、制造方面的說明或技術要求。 研究計劃及預期成果 研究計劃： 2012年11月12日-2012年12月25日：按照任務書要求查閱論文相關參考資料，填寫畢業設計開題報告書。 2013年1月11日-2013年3月5日：填寫畢業實習報告。 2013年3月8日-2013年3月14日：按照要求修改畢業設計開題報告。 2013年3月15日-2013年3月21日：學習并翻譯一篇與畢業設計相關的英文材料。 2013年3月22日-2013年4月11日：設計減速機箱體和箱蓋的結構并畫出相關草圖 2013年4月12日-2013年4月25日：完善設計所需的各種零件圖、夾具圖，并對設計的所有數據進行整理，做好撰寫畢業論文的準備。 2013年4月26日-2013年5月20日：畢業論文撰寫和修改工作。 預期成果： 機械制造技術設計是培養機械工程類專業學生應職應崗能力的重要實踐性教學環節，它要求學生能全面綜合地運用所學的理論和實踐知識，進行零件機械加工工藝規程和工藝裝備的設計。其基本目的是： 1） 培養工程意識。 2） 訓練基本技能。 3） 培養質量意識。 4） 培養規范意識。 特色或創新之處 1、 設計了一副可以多方面加工的夾具，減少了原材料的應用和所需的工時。 2、 設計了多種加工方案，并對其比較，選出最佳方案。 已具備的條件和尚需解決的問題 1、一是對鏜床的不熟悉，二是在公差與配合方面的知識所學較少。 2、學院圖書館相關資料有限，并且很多資料不外借處學校，設計此項目任務重工作量大物力條件有限以及經濟上的原因造成難以落實原材料加工出成品 3、經過努力，設計達到了預想的成功，由于條件的限制沒能加工出成品，但對于我自己來說已經學到了不少東西。 指導教師意見 指導教師簽名： 2011年 11 月 20 日 教研室（學科組、研究所）意見 教研室主任簽名： 年 月 日 系意見 主管領導簽名： 年 月 日 英文原文 Mineral product monorail reduction gear synopsis First:what is reducer Reducer is a dynamic communication agencies, the use of gear speed converters, motor rotational speed reducer to the Rotary to be few, and have greater torque institutions. The reducer role 1) velocity at the same time increase the output torque, torque output ratio by motor output by slowdown, but the attention should be paid to exceed the rated torque reducer. 2) the speed at the same time reduce the inertia load, the inertia of deceleration than reduced to the square. We can look at the General Motors has a value of inertia. ?????????? The type of reducer General helical gear reducer has reducer (including parallel shaft helical gear reducer, a worm reducer, bevel gear reducer, etc.), planetary gear reducer, Cycloid reducer, a worm reducer, a planetary friction CVT mechanical machines. ???????? Common reducer 1) worm reducer is the main characteristics of a reverse self-locking function, can be larger than a slowdown, input shaft and output shaft axis is not the same, nor in the same plane. But generally larger, transmission efficiency is not high, the accuracy is not high. 2) Harmonic Harmonic Drive reducer is controllable using flexible components to transfer elastic deformation and dynamic movement, not volume, high precision, but the disadvantage is that flexible wheel limited life, impatient shocks, rigidity and pieces of metal relatively poor. Not too high speed input. 3) planetary reducer its comparative advantage is compact structure, the return gap small, high precision, and have a long life span rated output torque can be done great. However, a price slightly expensive, the requirements of parts before assembly 1. Rolling cleaning with gasoline, kerosene other parts cleaning. All parts and Xiangbenna not allowed to have any impurities exist. Gear box and the inner wall (Worm), unprocessed surface has not been coated twice erosion-resistant oil paint, box has the outer surface coated primer and paint color (color requested by host). 2. Parts coated with a face wash after lubricants Second, the requirements of installation and adjustment 1. Rolling installation Rolling bearing inner ring should be installed at the shaft shoulder close to gap must not pass 0.05 mm thick Cypriot feet. 2. Bearing axial clearance of the clearance can not be adjusted bearings (such as deep groove ball bearings), axial clearance of 0.25 to 0.4 mm; the clearance adjustable bearing axial clearance numerical table. Click Tapered Roller Bearings axial clearance; angular contact ball bearing axial clearance 3. Gear (Worm) meshing tooth space available Cypriot side foot of lead or pressure. Will be lead wire on the alveolar, and then turning gear and squash lead wire, measuring two teeth side was crushed lead wire thickness and the size of which is adjacent teeth. 4. Tooth contact dot cylinder gear tooth contact Dot 2-10-4; bevel gear tooth contact Dot 2-11-4; Gearing contact Dot 2-12-4 Third, seal requirements 1. Box partition between the surface does not allow any pads filled, but can be coated or water glass sealant to ensure that the seal; 2. Assembly, the bolt tightening box, before using 0.05 mm Cypriot-foot inspection Covers Block with me and between the sealing surface; 3. Shaft seal should stretch to smear grease. The seal should be installed in strict accordance with the requirements Forth, lubrication requirements 1. Rationally determine the types of lubricants and greases and grades 2. Bearing lubrication fat, grease filled in the general Fatliquor space can be 1 / 2 to 2 / 3. 3. Lubricants should be regularly replaced, the new reducer used for the first time, the operation of oil-7 ~ 14 days, according to the situation can be after every 3 to 6 months for first oil. Fifth, the test requirements 1. Empty operation: at rated speed is, anti-running 1 to 2 hours; 2. Load test: at rated speed, rated load operation, the oil temperature balance to date. On the gear reducer, requested the pool temperature is not more than 35 oC, bearing temperature rise no more than 40 oC; the worm reducer, requested the pool temperature not more than 60 oC, bearing temperature of not more than 50 oC; 3. Entire testing process for the smooth operation, noise, not loosening the fixed link, sealed, not with the Sixth, packaging and transportation requirements 1. Protruding shaft and its annex should Oiler packaging; 2. Handling, lifting may not use screw rings and lug all of the above technical requirements are not necessarily listed, and sometimes also by other projects, mainly by the specific design requirements. Seventh. Technical requirements 1. Assembly, all parts cleaning with kerosene, gasoline Rolling cleansing, while the existence of any debris. Oil is not painted wall corrosion coatings twice; 2. Backlash with lead wire mesh test of not less than 0.16 mm, lead wire Backlash may not exceed the smallest of the four times; 3. Used Tu-color dot test. Tooth high point of contact by not less than 40% of contact spots on teeth not less than 50 per cent. Can be used when necessary, grinding or scraping after grinding to improve contacts; 4. Bearing axial clearance should be adjusted: φ40 0.05 - 0.1 mm, φ55 0.08 - 0.15 mm; 5. Test reducer subdivision surface, the contact surface and seal, oil spills are not allowed. Split-Tu allowed to paint or water glass seal and allow the use of any filler; 6. Engine lubricants to the contents N100 provisions height; Below I introduce our country reduction gear the development present situation First, the domestic reduction gear many by the gear drive, the worm drive primarily, but has the power and the load ratio generally is small, or velocity ratio great and mechanical efficiency excessively low question.Moreover, in the material quality and the technological level also has many weakness, the large-scale reduction gear question is specially more prominent, the service life is not long.The domestic use large-scale reduction gear (above 500kw), many from overseas (for example Denmark, Germany and so on) imports The 60's start few tooth reduction gears and so on difference transmission, cycloid pin gear transmission, overtone transmission which produces has the velocity ratio to be big, volume small, mechanical efficiency higher merit? .But its transmission theory limit, cannot transmit the oversized power, the power all must be smaller than generally 40kw. Because in the transmission theoretically, the technological level and the material quality aspect has not broken through, therefore, has not been able fundamentally to solve the transmission power in a big way, the velocity ratio big, the volume small, the weight light, mechanical efficiency higher these requests basically.The 90's initial period, the home appears three links (gear) the reduction gear, is one kind of outside stable motion gear drive reduction gear, it may realize the great velocity ratio, transmission load ability is also big. Its volume and the weight are all lighter than the dead axle speed reducer gear, the structure is simple, the efficiency is also high.Because this reduction gear three axle parallel structure, therefore caused the power/volume (or weight) the ratio is still small.Also its input axis and the output shaft on the identical spool thread, this do not have in the use many inconveniently. Not only Beijing Institute of Technology develops in successful " stable motion speed reducer gear " to have outside three link reduction gear merit, but also has the big power/weight (or volume) the ratio, as well as the input axis and the output shaft on identical spool thread merit, is at the domestic leading position.The home has the minority college and the factory and mining enterprise does the research work to in stable motion gear drive certain principles, has published some research paper, in has done some work using the cycloidal tooth crop rotation stable motion reduction gear. Second, the stable motion speed reducer gear principle of work synopsis, the stable motion speed reducer gear is refers to in a counter gear transmission, a gear in the stable motion generator actuation mean plane parallel motion, meshing through tooth profile between, actuates another tooth crop rotation dead axle to decelerate the rotation, the realization reduction gear function.The stable motion generator may use the parallelogram organization, either sine organization or cross slide organization.This achievement uses the parallelogram organization to take the stable motion generator. The stable motion generator may be the hypothesized use parallelogram organization, also may be the entity use parallelogram organization.Has the practical value stable motion gear mechanism for in counter gear organization, therefore may divide into the internal tooth crop rotation stable motion movement and the external tooth crop rotation stable motion movement two kind of situations.Outside the stable motion gear reduction organization, its internal tooth crop rotation stable motion movement, actuates the external gear and makes the deceleration rotation output.This organization also calls three links (gear) the reduction gear. As a result of the internal tooth crop rotation stable motion, two crank centers establish outside the annular gear tooth ring, therefore its size is not compact, cannot solve the volume major problem.? In stable motion gear reduction, its external tooth crop rotation stable motion movement, actuation internal tooth crop rotation deceleration rotation output.As a result of the external tooth crop rotation stable motion, two crank centers can establish in the external gear tooth ring, reduced the organization overall size greatly. Because in stable motion gear mechanism transmission efficiency high, volume small, input output coaxial line, therefore by widespread application prospect. Third, this project technical characteristic and key technologies? 1. this project technical characteristics, in this new " stable motion speed reducer gear " and domestic and foreign had the speed reducer gear compares, has the following characteristic: (1) velocity ratio scope is big, gets up from I=10, may reach most greatly several thousand.If manufactures the great velocity ratio the reduction gear, then demonstrates this reduction gear the merit.(2) transmission power scope is big: And may connect a body manufacture with the electric motor. (3) structure simple, the volume small, the weight is light.Reduces about 1/3 compared to the existing speed reducer gear.(4) mechanical efficiency is high.95 (5) this reduction gear input axis and the output shaft are on the identical spool thread.This reduction gear see Table 1 with other reduction gear performance comparison. Because lacks the data, various reduction gears power/load ratio which in the table arranges in order is most superior.? Table 1? Each kind of reduction gear comparison model power (kw) reduction gear ratio quality (kg) QI-450? 93 31.5 1820 ZSY-250? 95 31.5 540 NGW-92 88.1 31.5 577 SEW (Germany)? 90 28.61 1300 NP-100? 100 30 400 Note: NP-100 is in the stable motion speed reducer gear, the SEW reduction gear quality contains the electrical machinery.2. this project key technologies? May know by Figure 2, in “stable motion speed reducer gear " is by annular gear Z2, external gear Z1 and the parallelogram organization combination becomes.Its transmission principle is: The electrical machinery input rotary motion, the external tooth crop rotation parallel migration, its center of circle path is a circle, makes the dead axle rotation with it meshing annular gear. Because external tooth crop rotation parallel migration, therefore name stable motion gear mechanism.The gear parallel migration needs to have the auxiliary body help realization, may use (6~12) to sell the axis, the roller takes the hypothesized auxiliary stable motion organization, also may use the eccentric shaft to take the entity auxiliary stable motion organization.In the stable motion speed reducer gear key technologies and the essential craft are the composition parallelogram component size computation and the request processing precision, the gear teeth main parameter choice. These factors will all affect the transmission ability and the transmission quality.Overall speaking, the group cost reduction gear various spare parts all request to have the high precision, they will be deciding the reduction gear overall transmis3. this project survey this project has obtained the Chinese practical new patent, the patent number: ZL95227767.0? .? This project trial produced the first prototype from 1995 (power 2.5kW, after velocity ratio I=32), with some factory and mine cooperation, has one after another designed following several kind of different powers, the different velocity ratio reduction gear.(1) electrically operated on rollers gate uses the reduction gear, power 550W, velocity ratio I=26, is united as one body with the electrical machinery.sion quality. (2) mixer uses the reduction gear, power 370W, velocity ratio I=17.(3) some military goods use two kind of reduction gears, one kind of power 370W, velocity ratio I=23.5; Another kind of power 370W, velocity ratio I=103 two level of transmission reduction gear.(4) steel mill large package rotary abutment reduction gear, power 7.5kw, velocity ratio I=64.(5) steel mill table reduction gear, power 7.5kw, transmission I=11. In this patent foundation, has developed one kind of new ultra-large reduction gear, the power may reach 1000kw, at present is developing subminiature (outlook size for a millimeter level) miniature reduction gear. Graduation design task First, a design Monorail Driver Design reducer Second, the design of the original data 1 Monorail drive reducer Power Rating: 7.5 KW; 2 Monorail reducer drive the total transmission ratio: 15 around; 3 Monorail reducer drive car driven by the side of the output shaft from the race distance of not more than 200 mm; 4 Monorail reducer drive the total length of less than 420 mm, the width is not more than 450 mm and the total height of not more than 690 mm; Third, the equipment and the working environment This can be used to mine underground, open-air, dust, humidity, air quality, bad comparison bad work environment, and the operational requirements of a safe space. Fourth, the design requirements To meet the application requirements under the premise that the minimum cost of manufacturing. From the following aspects considered; (L) to streamline the shape of each parts, machinery simple structure; ??? (2) merge the functions of spare parts, reducing the types or quantities of spare parts; ??? (3) Application of the new structure, new technology, new materials, product reliability; ??? (4) decomposition components, its assembly, the assembly of the most simple structure; ??? (5) similar to parts of the division; ??? (6) standards for similar products by product serial number sequence analysis; ??? (7) The realization of the common parts of the product and standardization. ??? (8) assembly equipment design a map (0), the Six Parts (3), the design specification of a (not less than 30,000 words), and the design of technical and economic analysis. 中文譯文 一、 什么是減速器 減速器是一種動力傳達機構，利用齒輪的速度轉換器，將馬達的回轉數減速到所要的回轉數，并得到較大轉矩的機構。 1、減速器的作用 1）降速同時提高輸出扭矩，扭矩輸出比例按電機輸出乘減速比，但要注意不能超出減速器額定扭矩。 2） 減速同時降低了負載的慣量，慣量的減少為減速比的平方。大家可以看一下一般電機都有一個慣量數值。 2、減速器的種類 一般的減速器有斜齒輪減速器(包括平行軸斜齒輪減速器、蝸輪減速器、錐齒輪減速器等等)、行星齒輪減速器、擺線針輪減速器、蝸輪蝸桿減速器、行星摩擦式機械無級變速機等等。 3、常見減速器 1） 蝸輪蝸桿減速器的主要特點是具有反向自鎖功能，可以有較大的減速比，輸入軸和輸出軸不在同一軸線上，也不在同一平面上。但是一般體積較大，傳動效率不高，精度不高。 2） 諧波減速器的諧波傳動是利用柔性元件可控的彈性變形來傳遞運動和動力的，體積不大、精度很高，但缺點是柔輪壽命有限、不耐沖擊，剛性與金屬件相比較差。輸入轉速不能太高。 3） 行星減速器其優點是結構比較緊湊，回程間隙小、精度較高，使用壽命很長，額定輸出扭矩可以做的很大。但價格略貴一、對裝配前零件的要求 ： 1.滾動軸承用汽油清洗，其他零件用煤油清洗。所有零件和箱體內不許有任何雜質存在　。箱體內壁和齒輪（蝸輪）等未加工表面先后涂兩次不被機油侵蝕的耐油漆，箱體外表　面先后涂底漆和顏色油漆（按主機要求配色）。 2.零件配合面洗凈后涂以潤滑油 二、安裝和調整的要求　 1.滾動軸承的安裝　　滾動軸承安裝時軸承內圈應緊貼軸肩，要求縫隙不得通過0.05mm 厚的塞尺。 2.軸承軸向游隙　　對游隙不可調整的軸承（如深溝球軸承），其軸向游隙為0.25~0.4mm；對游隙可調整　　的軸承軸向游隙數值見表。點擊查看圓錐滾子軸承軸向游隙；角接觸球軸承軸向游隙　 3.齒輪（蝸輪）嚙合的齒側間隙　　可用塞尺或壓鉛法。即將鉛絲放在齒槽上，然后轉動齒輪而壓扁鉛絲，測量兩齒側被　　壓扁鉛絲厚度之和即為齒側的大小?！? 4.齒面接觸斑點圓柱齒輪齒面接觸斑點2-10-4；圓錐齒輪齒面接觸斑點2-11-4；蝸桿傳動接觸斑點2-12-4 三、密封要求　 1.箱體剖分面之間不允許填任何墊片，但可以涂密封膠或水玻璃以保證密封；　 2.裝配時，在擰緊箱體螺栓前，應使用0.05mm的塞尺檢查箱蓋和箱座結合面之間的密封性；　 3.軸伸密封處應涂以潤滑脂。各密封裝置應嚴格按要求安裝 四、潤滑要求　 1.合理確定潤滑油和潤滑脂類型和牌號　 2.軸承脂潤滑時，潤滑脂的填充量一般為可加脂空間的1/2~2/3。　 3.潤滑油應定期更換，新減速器第一次使用時，運轉7~14天后換油，以后可以根據情況每隔3~6個月?lián)Q一次油。 五、試驗要求　 1.空載運轉：在額定轉速下正、反運轉1~2小時；　 2.負荷試驗：在額定轉速、額定負荷下運轉，至油溫平衡為止。　　對齒輪減速器，要求油池溫升不超過35oC,軸承溫升不超過40oC；　　對蝸桿減速器，要求油池溫升不超過60oC,軸承溫升不超過50oC；　 3.全部試驗過程中，要求運轉平穩，噪聲小，聯接固定處不松動，各密封、結合處不 六、包裝和運輸要求　 1.外伸軸及其附件應涂油包裝；　 2.搬運、起吊時不得使用吊環螺釘及吊耳以上技術要求不一定全部列出，有時還需另增項目，主要由設計的具體要求而定。 七、技術要求　 1.裝配前，所有零件用煤油清洗，滾動軸承用汽油清洗，不許有任何　　雜物存在。內壁涂上不被機油腐蝕的涂料兩次；　 2.嚙合側隙用鉛絲檢驗不小于0.16mm，鉛絲不得大于最小側隙的4倍；　 3.用涂色法檢驗斑點。按齒高接觸點不小于40%；按齒長接觸斑點不　　小于50%。必要時可用研磨或刮后研磨以便改善接觸情況；　 4.應調整軸承軸向間隙：φ40為0.05--0.1mm,φ55為0.08--0.15mm;　 5.檢驗減速器剖分面、各接觸面及密封處，均不許漏油。剖分面允許　　涂以密封油漆或水玻璃，不允許使用任何填料；　 6.機座內裝N100潤滑油至規定高度。 八、下面我介紹我國減速器的發展現狀 （一）、國內的減速器多以齒輪傳動、蝸桿傳動為主，但普遍存在著功率與重量比小，或者傳動比大而機械效率過低的問題。另外，材料品質和工藝水平上還有許多弱點，特別是大型的減速器問題更突出，使用壽命不長。國內使用的大型減速器（500kw以上），多從國外（如丹麥、德國等）進口。60年代開始生產的少齒差傳動、擺線針輪傳動、諧波傳動等減速器具有傳動比大，體積小、機械效率高等優點?。但受其傳動的理論的限制，不能傳遞過大的功率，功率一般都要小于40kw。由于在傳動的理論上、工藝水平和材料品質方面沒有突破，因此，沒能從根本上解決傳遞功率大、傳動比大、體積小、重量輕、機械效率高等這些基本要求