HIGSPEEDBUFFINGMACHINE高速拋光機
5 / 4讓后輪著地,向1.3.3 HIGH SPEED BUFFING MACHIN 高速拋光機Operati on seque nee操作程序Let the traili ng wheel touehdow n, lea n back the buffi ng maeh ine un til the han dle touch the floor. 后傾斜拋光機,直至手柄放在地上;文檔來自于網絡搜索逆時針旋轉出黃色中心鎖緊螺釘;文檔來自于網Cou nterclockwise rotate out the locked screw in the yellow cen ter. 絡搜索Place the polishi ng pad steadily on the driver, and screw tightly the bolt in the yellow cen ter.把所需的拋光墊安放在拋光墊驅動器上,擰緊黃色中心鎖緊螺釘;文檔來自于網絡搜索Restore the high speed buffi ng mach ine un til it stands erectly.將高速拋光機恢復至直立位置;文檔來自于網絡搜索Lift the relax ing han dle bar and put dow n the han dle, which make the head of the buffi ng mach ine float freely upand dow n.提起手柄放松桿,放下手柄,使拋光機頭可上下自由浮動。文檔來自于網絡搜索Connect the electricity line with the plug which connects with thegrounding line, and put through the powersupply.將電源線插入有接地線的插座上,接通電源。文檔來自于網絡搜索Press dow n the safety lock butt on, and rotate forwards the revolv ing han dle, and start the high speed buffi ngmachi ne. When the mach ine works, leave the thumb out of the safe locked butt on.按下安全鎖定按鈕,向前轉動旋轉手柄,開動高速拋光機。機器開動后,把拇指從安全鎖定按鈕上放開。文檔來自于網絡搜索XingImpel the high speed buffi ng machi ne forward, or make it move with a“ W it in erary, start polish on the walayer of the floor, and it should keep the buffi ng machi ne moving, so as not to damage the wax layer and the floorboard layer.向前推動高速拋光機,或移動高速拋光機走“ W形,開始對地板打蠟層拋光。要使高速拋光機保持移動,以免損壞打蠟層和地板層面。文檔來自于網絡搜索In order to prevent the over loading of the motor, there is the protector matched to the electro circuit of the machi ne. If the breaker shut dow n, it should wait 15 sec onds to make the machi ne repositi on.為了防止電動機過載,機器配有電路過載保護裝置。斷路器若斷路,必須等待15秒鐘后,方可使其復位。文檔來自于網絡搜索In the end of the polishing work in the waxing layer of the floor board, rotate the revolving handle backwards;make the butt on of the safety lock separated, the n the high speed buffing machi ne stop rotat ing.地板打蠟層拋光結束,向后轉動旋轉手柄,安全鎖定按鈕脫開,高速拋光機停止轉動。文檔來自于網絡搜索When the work is fini shed, lea n back the high speed buffi ng machi ne, with the trail ing wheel touchdow n, in orderavoid ing the damage of the polish ing pad. Or unl ade the pad to protect it.工作完畢,保持高速拋光機向后傾斜,后輪著地,防止拋光墊損壞,或采取卸下拋光墊的方式保護拋光墊。文檔來自于網絡搜索The maintenance of high speed buffi ng machi ne高速拋光機的維護保養 /文檔來自于網絡搜索Every time whe n finish the use, it should unl ade the polish ing pad so as to avoid any damage to the pad.每次使用后,應卸下拋光墊,可防止拋光墊損壞。文檔來自于網絡搜索Keep the machi ne lea ning backward; keep the traili ng wheel touchdow n the floor.保持機器向后傾斜,后輪著地存放。文檔來自于網絡搜索After every time use, it should clea n the mach ine, wipe off the buffi ng compou nds, the dust and smear.每次使用后,清埋機座,擦拭清除拋光劑和灰塵、污垢。文檔來自于網絡搜索 After each time use, it should use the hot water to clea n the polish ing pad.每次使用后,用熱水清洗拋光墊。文檔來自于網絡搜索« Twist the electricity lines on the suspended hook. Use the wet dust cloth to wipe the surface of the electricity line. Once foun ded damaged, it should replace immediately.將電源線纏繞在懸掛鉤上。用濕抹布,擦拭電源線表面。發現電源線損壞,應立即更換文檔來自于網絡搜索« Before being produced out of the factory, the gear wheel of the high speed buffi ng mach ine and the tra nsmissi on system of the motor and so on have bee n lubricate d, so they don ' t n eed to use the lubricat ing age nt. 高速拋光 機齒輪、電動機等傳動系統出廠前已潤滑,使用中無需潤滑。文檔來自于網絡搜索Safety notification of the high speed buffi ng machi ne.高速拋光機安全注意事項文檔來自于網絡搜索It can ' t use the high speed buffi ng machi ne on the followi ng con diti on s.發現以下情況不得使用高速拋光機文檔來自于網絡搜索The operator doesn' t experienee professional training. 操作者未受過專業培訓;文檔來自于網絡搜索The operator doesn' t learn anything of the <safely operating procedure>操作者未學習過安全操作規程; 文檔來自于網絡搜索The operati on of the high speed buffing machi ne is on un usual con diti on.高速拋光機運轉處于不正常的條件下。文檔來自于網絡搜索Before using the high speed buffi ng machi ne, it should check the follow ing items towards the en viro nment.使用高速拋光機前,應對環境作以下檢查:文檔來自于網絡搜索Know about the loose substance on the wax layer of the floor. If the loose substance sticks on the revolving pad, it will turn into dan gerous projector.清楚地板打蠟層上的松散物。松散物若粘在旋轉的拋光墊上,會變成危險的拋射物。文檔來自于網絡搜索Check whether there are flammable liquid or gas in the environment of the polishing floor board, if there is, itshould take some safety measures.檢查被拋光地板的環境內有無易燃液體或氣體,若有應采取安全措施。文檔來自于網絡搜索Check the electricity line and the plug of the power source, to see whether there is any damage.檢查電源線和口電源插座、插頭有無損壞。文檔來自于網絡搜索When using the high speed buffing mach in e, it should pay atte nti on to the follow ing items.使用高速拋光機時應注意以下事項:文檔來自于網絡搜索The hands and feet should keep far from the revolv ing polish ing head.操作者的手、腳要遠離旋轉的拋光頭。文檔來自于網絡搜索The operator can ' t step on the power source lines or twist the lines into the polishing head.操作者不得踩住電源線或電源線纏入拋光頭內。文檔來自于網絡搜索The operator must wear special uni forms for the safe side.操作者必須安全著裝。文檔來自于網絡搜索The polishing area can' t exceed the length of the electricity line.拋光區域不得超過電源線的長度。文檔來自于網絡搜索When operating, it should not let go hold of the operating handle. When the electricity is cut, it should wait until the buffi ng machi ne stop revolvi ng then can relax the han dle.操作時不得擅自將操作手柄脫手。停機時,必須在高速拋光機完全停止旋轉后,方可松開手柄。文檔來自于網絡搜索。It can ' t use the polishing pad which stick the dust and smear on. When it pad depositing too much dust and canclea ned thoroughly, it should be replaced on time.不能使用粘有灰塵、污垢的拋光墊拋光。積垢太多的拋光墊無法清洗干凈時,應及時更換文檔來自于網絡搜索When replacing or installing the polishing pad, it should cut of the electricity power.更換、安裝拋光墊時,必須 切斷電源。文檔來自于網絡搜索After stopp ing the use of the high speed buffing machi ne, it should pay atte nti on to the follow ing items.停止使用高速拋光機后應注意以下事項: 文檔來自于網絡搜索Cut off the power source 切斷電源。Lea n back the mach ine; make the traili ng wheel touchdow n the floor.向后傾斜,后輪著地存放。文檔來自于網絡搜索Don' t lay outdoor; it should save in a dry place.不得在室外存放,并應存放在干燥處。 文檔來自于網絡搜索Malfu nction and solution table for high speed buffi ng machi ne高速拋光機故障分析和排除方法見下表:文檔來自于網絡搜索Malfu nctio n 故障Reas on 原因Solution 排除方法The electro motor doesn ' t work電動機不轉動The machine is not connected with the electricity power 機器未接電源Connect the electricity power. 插上電源Brake跳閘Restore the break of the machine, which require 15 seconds to start the machine確定原因,恢復機器斷路器(必須等15秒后方可啟動機器)Building circuit breaker damaged 斷路器建筑物斷路器跳閘Restores the circuit breaker or changes to other power sources恢復斷路器或改用其它電源The power line is not right 電源線不對Contacts with the specialized serviceman聯系專業維修人員The wiring is not right 接線不對Rotating handle switch broken 扭轉柄開關故障Malfunction of the rectifier 整流器故障The circuit breaker continuously cut down斷路器連續跳閘Too much dust and smear deposited on the polishing pad拋光墊積塵、污垢太多Change the polishing pad 更換拋光墊Wrong chooseof the polishing pad 拋光墊選擇不當Change the adequate polishing pad更換合適的拋光墊Breaker damaged 電路斷路器損壞Connect with professional maintenance staffs 聯系專業維修Carbon brush motor damaged 電動機碳刷磨損人員The revolving speed of the polishing pad is slow or doesn work at all拋光墊旋轉速度慢, 或跟本不轉Slacken of the transmission tape 傳動膠'帶松弛Adjust the elasticity of the transmission tape調整傳動膠帶松緊度Rupture of the transmission adhesivetape傳動膠帶斷裂Change the transmission tape 更換傳動膠帶