裝配圖變速器扭矩測量及其標定裝置設計（有cad圖）,裝配,變速器,扭矩,測量,丈量,及其,標定,裝置,設計,cad 變速器扭矩測量及其標定裝置設計 摘 要 本說明書主要是設計變速器一軸扭矩測量及標定裝置，而扭矩傳感器的選擇和傳輸方式的選擇是本次設計的重點。 扭矩傳感器選擇了電阻應變片式，傳輸方式選擇了軸通式，而四個應變片接成全橋，然后引出線接到四個集流環上，集流環與軸一起轉動，電信號再通過電刷（設計成起落架式電刷，為了減少磨損）傳輸給PCM數據采集系統?？紤]到該設備所用的領域，對應變片處的直徑進行了計算，額定扭矩小于100N.m的變速器一軸均可測量。 本次設計參考了以往的設計，并進行了改進，后邊附有相關內容的參考文獻和附錄。 由于設計過程中貫穿了三化，大大的提高了其使用壽命和維修性。 標定裝置的設計主要考慮到如何加載的問題，選擇了一端用花鍵連接并用螺栓固定在實驗臺上，另一端用花鍵連接并與加載杠桿一起轉動，通過這種方式產生扭轉，并測試其軸的扭矩，繪制標定曲線。 關鍵詞：應變片式扭矩傳感器，集流環，PCM3132數據采集系統，標定裝置 DESIGN OF A TRANSMISSION SHAFT TORQUE MEASUREMENT AND CALIBRATION DEVICE ABSTRACT Summary of the manual transmission design is a shaft torque measurement and calibration equipment home, and torque sensor choice and the choice of the transmission mode of this design is the key. Torque Sensor choose strain gage type, the choice of the transmission mode shaft formula, and then four strain gauge make full bridge, then connect leading-out wire to four slip rings. Slip rings rotate with the axis. Electric signal transmitted to the PCM data acquisition system through brush. Taking into account the equipment used in the fields of the strain gauge the diameter, Rated torque less than 100 Nm fixation of a transmission shaft can be measured. The design references the previous design, and has an improvement, afterward with the relevant content of the references and appendices. As the design process through the three and greatly improved its service life and maintainability. Calibration device design mainly to the problem of how to feed one-end connected with spline and fixed on experimental stage with bolt and the other connected to spend bond with the loading lever rotation together, in this way have reversed, and test its axis torque, Drawing calibration curve. Key words: strain gages-torque sensor, slip ring, PCM3132 data acquisition system, calibration device 目 錄 第一章 前言.......................... ..................1 第二章 概述 ............................................3 第三章 扭矩傳感器方案分析 ..............................4 §3.1用電力測功器測扭矩.............................. 4 §3.1.1直流電力測功器測量扭矩..................... 4 §3.1.2交流電力測功器測量扭矩..................... 5 §3.1.3電渦流測功器測量扭矩....................... 5 §3.2 用扭矩儀測扭矩............................ ..... 6 §3.2.1電阻應變片式扭矩儀......................... 6 §3.2.2相位差扭矩儀............................... 9 §3.2.3 頻閃觀測式扭力計.......................... 10 §3.2.4 鋼弦式扭矩儀.............................. 11 §3.3 輔助裝置..................................... 12 §3.3.1傳輸裝置分析..............................12 §3.3.2 數據分析與采集系統.........................12 第四章 設計計算及結構分析........ .. ..................14 §4.1 零部件的設計計算...............................14 §4.1.1 離合器軸上貼應變片處直徑的確定.............14 §4.1.2 離合器軸和變速器一軸矩形花鍵連接長度的計算.14 §4.1.3 一軸上薄弱截面強度校核計算................15 §4.1.4 電橋輸出電壓的計算.........................15 §4.1.5 標定裝置力和扭矩曲線圖.....................16 §4.2 零部件的結構特點及加工工藝性分析...............18 §4.2.1測量裝置.........................18 §4.2.2標定裝置.........................18 第五章 結論....................................... ....20 參考文獻...............................................21 致謝...................................................22 III