摘 要往復活塞式壓縮機是容積式壓縮機的一種，是利用活塞在氣缸中對流體進行擠壓，使流體壓力提高并排出的壓縮機械。熱力、動力計算是壓縮機設計計算中基本的，又是最重要的一項工作，根據用戶提供的成分、氣量、壓力等參數要求，經過計算得到壓縮機的相關參數，如級數、列數、氣缸尺寸、軸功率等。經過動力計算得到活塞式壓縮機的受力情況。準確地分析機組受力情況，對于消除機組的振動非常重要。在變工況條件下，需要快速實現核算原設計的飛輪是否滿足運行要求?；钊綁嚎s機熱力計算、動力計算的結果將為各部件圖形以及基礎設計提供原始數據，其計算結果的精確程度體現了壓縮機的設計水平，也是壓縮機研究方面的一個課題。關鍵詞：活塞式壓縮機; 熱力計算; 動力計算;氣缸；曲軸AbstractReciprocating piston compressor is a volume compressor, which is to increase pressure to discharge fluid by piston. Thermal and dynamic compressor design is the basic and most important one, according to users with the content, gas, pressure and other parameters, calculated after the compressor related parameters, such as class, number, size cylinder, shaft power, and so on. After driving force calculated piston compressor of the force. It is very important to eliminate the vibration by accurate analysis of the force units. During alterative working conditions, it is need to meet the movement requirement for original design of flywheel rapidly. Thermodynamic and dynamic calculations of Piston compressor provide original data for unit graphics and basic design, the calculated results reflect the grade of the compressor design, and the compressor is a study of the topic. Keywords: piston-type compressors; Thermodynamic calculations; Dynamic calculation; Cylinder; Crankshaft recalculation目 錄中文摘要......................................................................................................................Ⅰ英文摘要......................................................................................................................Ⅱ第 1 章 緒論 ................................................................................................................11.1 用途和適用范圍 ........................................................................................11.2 工作原理 ................................................................................................11.2 活塞壓縮機特點 .......................................................................................1第 2 章 總體設計 ........................................................................................................22.1 結構方案的選擇 ........................................................................................22.2 電機的選擇 ..............................................................................................4第 3 章 熱力計算 ........................................................................................................53.1 給定條件 .................................................................................................53.2 結構形式及主要結構參數 ............................................................................53.3 熱力計算 .................................................................................................5第 4 章 動力計算 ........................................................................................................9第 5 章 汽缸部分的設計 ..........................................................................................115.1 汽缸 .....................................................................................................115.2 活塞 .....................................................................................................145.3 氣閥 .....................................................................................................145.4 活塞環 ..................................................................................................15第 6 章 基本部件的設計 ..........................................................................................166.1 機身、中體 ............................................................................................166.2 曲軸 .....................................................................................................166.3 連桿 .....................................................................................................226.4 軸承的選取 ............................................................................................29第 7 章 其他部件的設計 ..........................................................................................307.1 聯軸器 ..................................................................................................307.2 飛輪 .....................................................................................................30第 8 章 壓縮機的安裝、試車與調整 ......................................................................318.1 壓縮機的安裝 .........................................................................................318.2 壓縮機的試車 .........................................................................................318.3 壓縮機的調整 .........................................................................................318.4 壓縮機的維護和修理 ................................................................................318.5 活塞式壓縮機的常見故障分析及消除方法 .....................................................32第 9 章 結論 ..............................................................................................................34參考文獻 ......................................................................................................................35致謝 ..............................................................................................................................36